Skip to Content

Anker Soundcore Not Working (How To Fix/Reset)

The Anker Soundcore is a great choice for most audiophiles due to its classic design, great sound quality, long battery life, water resistance, and, most importantly, value for money.

However, it’s not immune to problems. Hence, you may not get to enjoy these features when your Anker Soundcore is not working. The section below identifies the various reasons for this failure and provides solutions to these problems.

Anker Soundcore not working can be due to a dead or faulty battery, wrong settings, or malfunctioning hardware. Recharge the battery or replace it. Replace the malfunctioning hardware and reset the device to resolve the issue.

black soundcore on the table

Anker Soundcore Not Turning On

black soundcore on the table

It can be frustrating when your Anker Soundcore won’t turn on, especially when you yearn to listen to your favorite music. Nonetheless, do not panic. Read the section below to identify the main reasons and learn how to fix the issue.

Anker Soundcore not turning on could be due to a faulty power button, drained or damaged battery, faulty circuit board, or previous Bluetooth settings. Recharge the battery and reset the device.

You can also take your Soundcore to the nearest Anker service center for battery, power button, and circuit board replacement.

Since Anker Soundcore has a 24-hour battery life, it’s possible to forget to charge it. Additionally, a faulty cable or adapter may not charge your device, so that it won’t turn on. Charge your Soundcore for at least three hours and ensure the cable and adapter work.

The power button may malfunction due to mechanical or electrical damage, causing your Anker soundcore to fail to turn on. Likewise, overcharging the battery may damage it. Hence, if it’s fully charged, but the soundcore won’t turn on, you should consider checking it.

Although Anker Soundcore is water resistant, continuous exposure to moisture may damage the circuit board. Thus, if you have tried all the above measures without success, take your device to the nearest Anker service center for professional diagnosis and replacement of the damaged parts.

Anker Soundcore Not Charging

confused man standing

Anker Soundcore has an inbuilt battery that you must charge to power it. Hence, the device won’t work if it won’t charge. The following troubleshooting guide explains the main reasons for this and how to fix the issue.

Anker Soundcore not working can be due to a damaged battery, loose or broken charging port, bad battery, or loose cable. Secure the charging cable and replace the charging port and battery to resolve the issue.

A loose or damaged cable won’t charge your Anker Soundcore. Hence, use the cable to charge another device; if it doesn’t, it’s most likely damaged and needs replacement. Additionally, a loose or damaged charging port can cause charging failure.

When you confirm that the cable is in good condition, ensure that the red light is on when you plug in the speaker to charge. If it isn’t, you may have a bad charging port that you need to replace.

Once you replace the cable and charging port but the speaker won’t charge, check the battery for faults. You may need to take your Soundcore to the nearest Anker service center for battery repair or replacement.

Anker Soundcore Not Pairing

black soundcore on the table

Anker Soundcore is a wireless speaker with an advanced Bluetooth feature and a wide connectivity range. However, you can’t connect it to the music source when it experiences pairing problems. The section below addresses the problem and suggests ways to resolve the issue.

Anker Soundcore not pairing could be due to a low battery, outdated Bluetooth drive, device not in pairing mode, or out-of-range. Charge the speaker, clear any obstructions and switch it to pairing mode. Update the Bluetooth drive and reset the device to resolve the issue.

Anker Soundcore, with a low battery, may experience pairing problems. Hence, charge the speaker for at least three hours using a wall charger with at least two amps output. Ensure the speaker is within range; if possible, place it beside your music source. In addition, remove other devices that could cause obstruction.

If your speaker won’t pair after trying the above hacks, disable and enable the Bluetooth feature and try to connect. Reset your device to clear any previous information and try pairing.

Copyright protected content owner: ReadyToDIY.com and was initially posted on October 8, 2022.

Update the Bluetooth drive to the latest version on your phone by going to the settings, select ‘About phone,’ tapping on a software update to install the latest version and resolve the issue.

Anker Soundcore Not Connecting To Laptop/Macbook

confused man standing

Anker Soundcore is famous for its powerful Bluetooth with instant connectivity to Alexa-enabled devices, iPhones, laptops, and tablets. But what do you do when it doesn’t connect to your laptop/Macbook? Read the section below to identify why this is happening and learn how to fix the issue.

Anker Soundcore not connecting to a laptop/Macbook can be due to low battery, previous connections, Bluetooth feature not turned on or not discoverable, outdated Bluetooth drive, or interference from smart devices. Update the Bluetooth drive, clear previous connections, and charge the speaker.

Anker Soundcore won’t connect to your laptop or Macbook with a low battery. In addition, you will have to switch on the Bluetooth feature on your computer or Macbook to pair with your speaker. Go to settings on your laptop or Macbook and set your Anker Soundcore as the default device. Ensure the Bluetooth is discoverable to pair with your speaker.

The Anker Soundcore won’t pair with your Laptop or Macbook when it’s out of range; hence, you should move it closer. Additionally, the speaker will pair with the last connected device; thus, you should clear any previous connections.

If you have smart devices in your home or office, they may interfere with Anker sound core Bluetooth connectivity. Move your laptop away from these devices and try reconnecting to your speaker.

Anker Soundcore could experience Bluetooth connection issues due to an outdated driver. In this case, update your Bluetooth drive to the latest version to resolve the issue.

Anker Soundcore Not Showing Up

black soundcore on the table

Your Anker Soundcore won’t connect to a phone or laptop if it doesn’t show up. It’s unfortunate because you won’t listen to your favorite music or enjoy your favorite movie. Luckily, it’s a minor problem that you can fix yourself. Read the following section to learn how to resolve the issue.

Anker Soundcore not showing up can be due to a low battery, the device not on pairing mode, or out of range. Charge your speaker and move it close to the music source. Switch on the Bluetooth feature and make it discoverable. Reset the device to resolve the issue.

Anker Soundcore won’t show up when the Bluetooth feature is off. In addition, it needs to be within range of the music source to show up. Hence, move the speaker in range and press the power button for a few seconds until the speaker glows.

Hit the Bluetooth button to initiate the pairing process. Go to the settings on your phone or laptop and search for the speaker to see if it’s visible. Reset the Anker Soundcore if the above measure fails to resolve the issue.

Anker Soundcore Not Turning Off

confused woman standing

An Anker Soundcore that won’t turn off can drain your battery and inconvenience you the next time you want to listen to your favorite music or watch a movie. You can resolve the issue by taking the necessary steps to identify the cause. Keep reading to learn the main reasons and how to fix them.

Anker Soundcore not turning on could result from a faulty power button or software malfunctions. Replace the broken button and restore your device to factory settings to clear software malfunctions and resolve the issue.

A worn-out Anker Soundcore power button won’t turn off your device; hence, replacing it will fix the issue. Likewise, software malfunctions can result in a Bluetooth device that won’t turn off. 

If the Soundcore does not turn off after replacing the power button, hold the on/off button until the device enters pairing mode. The device will automatically turn off after ten minutes if there is no audio signal. Alternatively, insert a paperclip into the audio jack and press the reset button to reset the device and resolve the issue.

Copyright article owner is ReadyToDiy.com for this article. This post was first published on October 8, 2022.

Anker Soundcore No Sound

black soundcore on the table

Great sound output is one of the distinguishing features of Anker Soundcore. It has two dual-range speakers and a perfectly tuned digital processor. As a result, it produces clear sound without distortions. But what do you do when your device has no sound?

Anker Soundcore no sound could be due to a low battery, broken speakers, the device not being connected to an audio source or not in range or wrong settings on the audio source. Recharge your appliance and repair/replace the damaged speakers. Input the right settings to resolve the issue.

Your Anker Soundcore will not produce any sound when not paired with the audio source or when it’s out of range. Hence, move the device closer and ensure it’s connected to the audio source. Likewise, it won’t produce sound when it has faulty speakers. Therefore, consider taking it to your nearest Anker service center for speaker repair or replacement.

The Anker Soundcore depends on the audio source settings to produce sound. Hence ensure to turn up the volume on the device and your phone or laptop. Reset your Anker Soundcore if the above measures do not successfully restore the sound.

Anker Soundcore Keeps Disconnecting

confused man standing

Anker Soundcore that keeps disconnecting can be annoying, especially when binge-watching a movie or listening to music. The following section discusses the common reasons and how to fix the issue.

Anker sound core keeps disconnecting due to power issues, an audio source out of range, interference from other devices, connection to multiple devices, or outdated software. Charge the device and move it closer to the audio source. Recharge the device and update the software to resolve the issue.

Your Anker Soundcore will keep disconnecting when there is interference from other devices. For instance, a Wi-Fi radio frequency may interfere with the device’s Bluetooth connectivity. Move it away from the router to avoid interference.

Power issues like low charge can interfere with your Anker Soundcore, thus it will keep disconnecting. In addition, if you have not updated your phone or laptop software in a while, it could face incompatibility issues causing your device to keep disconnecting.

Connect your Soundcore to a power source and charge for at least three hours. Ensure the cable works perfectly by connecting it to another appliance to test if it charges it. Install the latest software on your audio source and resolve the issue.

Anker Soundcore Keeps Beeping

black soundcore on the table

Anker soundcore that keeps beeping can be annoying, especially when craving a quiet ambiance or having sleeping kids. So, what do you do in this case? Do you need to get a new device?

Anker Soundcore keeps beeping to alert you of low charge, full battery, or when pairing with a new device. In addition, loose or damaged cables, debris, or outdated software can cause this problem. Replace the broken wires, remove dirt and update the software to resolve the issue.

Your Anker Soundcore will keep beeping to alert you of a low battery. In this case, connect the device to a power source to stop the sound. Additionally, the device will beep to alert you when charging is complete or successful in pairing with a sound source.

If the Soundcore doesn’t stop beeping after connecting to a power source, you could have a faulty cable or physical obstruction of the charging port due to dirt or grime. Replace the cable and clean off any dirt.

Your Anker Soundcore will keep beeping when you connect it to a power source with a higher or lower than the recommended voltage. Unplug the device when this happens to avoid damaging it. In addition, outdated software can cause various malfunctions with your device, including strange beeping. In this case, update the software and reset the device to resolve the issue.

How To Reset Anker Soundcore

confused woman standing

When your Anker Soundcore runs into problems, your normal reaction would be to take it to the nearest service center for repair. However, you can fix most of these problems by resetting the device. So, read the section below to learn how to reset your device and fix various not working issues.

To reset Anker Soundcore, press and hold the power button for eight seconds, followed by the Bluetooth button for two seconds. You will see the blue LED light blinking indicating that your device is fully reset.

Resetting your Anker Soundcore is a simple, straightforward process that only takes a few seconds.

Step 1: Press the power button for eight seconds.

Step 2: Press and hold the Bluetooth button for two seconds. 

Step 3: The blue LED light will start blinking, indicating that your device is fully reset.

ReadyToDIY is the owner of this article. This post was published on October 8, 2022.

If your Anker Soundcore isn’t working, it can be because of a bad or dead battery, incorrect settings, or broken hardware. Replace or recharge the battery. Swap out the broken hardware and restart the device to fix the problem.