Skip to Content

Resetting Bradford White Water Heater

When it comes to having hot water readily available, those who own a Bradford White water heater don’t have to often think of the availability of such. However, if a reset is needed to get this plumbing feature up and running again, what does the process entail?

To reset a Bradford White water heater, turn the water heater off and allow it to sit for five minutes so all gas can clear. Turn the heater to ‘Pilot Mode,’ hold down the same button, and tandem press the red button beneath until a click can be heard and the ‘Status’ light blinks green.

Resetting water heater

A Bradford White water heater is designed to supply hot water to users with the simple turn of a faucet, making having access to heated water easy and nearly thoughtless. Although this is typically the case for most owners of this plumbing feature, there are times when certain functions may go awry and require a reset in order to be restored. If you own a Bradford White water heater and are looking to reset it, continue reading to find the steps to take.

Resetting Bradford White Water Heater

Water heaters may seem relatively simple at first glance, due to the ease at which they are able to provide owners with hot water within a matter of seconds once the water tap starts running. Even with the ease in which hot water can be retrieved from this device, there are many working parts that must all function properly in order to provide heated water to any home or business. If you notice that your Bradford White water heater is not working as it should, how can it be reset?

To reset a Bradford White water heater, turn the water heater off and allow it to sit for five minutes so all gas can clear. Turn the heater to ‘Pilot Mode,’ hold down the same button, and tandem press the red button beneath until a click can be heard and the ‘Status’ light blinks green.

It may take a few attempts until you hear the single click once you press the square red button beneath the knob where ‘Pilot Light’ can be found, but be sure you continue to hold down the knob as you press the button. When the ‘Status’ light blinks green, you will then release the knob and turn it to ‘Hot.’ Once the knob has been turned, you should be able to hear the pilot light ignite, which indicates the reset was successful.

Is There a Reset Button On a Bradford White Water Heater?

Man checking the water heater tank

For many different appliances and devices, manufacturers have installed a designed reset button which can be pushed when certain functions are not operating properly or the memory needs to be cleared from a particular item. This allows users to easily reset the device without having to worry about taking multiple steps to complete such a process and makes resetting whatever device or appliance they are working with quick and easy.

There is not a designated reset button located on a Bradford White water heater. Although some brands do host this feature, with a Bradford White water heater, owners need to follow simple steps to reset the device which should only take a few minutes from start to finish.

Copyright protected content owner: ReadyToDIY.com and was initially posted on May 5, 2022.

Although it would seem that an installed reset button would be the most logical route to aiding owners when their plumbing fixture needs a reset, Bradford White water heaters do not host this feature, but this does not mean the device cannot be easily reset. The process to reset a Bradford White water heater is simple and the steps to complete a reset can be found in the previous section titled “Resetting Bradford White Water Heater.”

How to Reset Bradford White Water Heater

Man checking the water heater tank

It may never occur to Bradford White water heater owners that there could come a time when their heater needs to be reset, as these plumbing fixtures tend to operate for years without much trouble. However, if you experience power loss, have various components of the heater that seem to be having trouble functioning, or simply desire to get your heater working at a more efficient rate, a reset could be just the trick, but how can this be done?

To reset a Bradford White water heater, turn the heater off and allow five minutes for all gas to escape. You will then turn the knob to ‘Pilot Mode,’ continue to hold the knob, and press the red button directly below the knob until a click can be heard and the ‘Status’ Light flashes green.

Once the status light on your water heater is flashing green, you will then release both buttons and switch the knob to ‘Hot’ water. When this is done, you should be able to hear the pilot light ignite, which indicates that the reset has completed successfully. It should be noted that it may take a few presses when holding down the button below the pilot knob, but once you hear a click, you can then move forward with igniting the heater and using it as normal.

How to Reset Bradford White Water Heater Gas Valve

Man fixing the water heater

When it comes to the primary components that owners think of when pondering their Bradford White water heater, the most common include the pilot light and the control knob. These are the most familiar items for many, but there are so many other components to this plumbing feature that play a major role in its operation, such as the gas valve. If the gas valve is not allotting the right flow of gas to your water heater and needs to be reset, how can this be done?

Copyright article owner is ReadyToDiy.com for this article. This post was first published on May 5, 2022.

To reset a Bradford White water heater gas valve, you have to reset the unit as a whole. To do this, turn off the water heater and wait five minutes. You will then turn the knob to ‘Pilot Mode,’ continue to hold it in, and press the button directly beneath it until the ‘Status ‘ Light blinks green.

The gas valve of a Bradford White water heater is the component that opens and closes gas flow so that the pilot light can ignite. If the gas valve is not opening or closing and you are thus having issues getting the water heated, a reset may be the exact step needed to get things back on track. However, if you inspect the gas valve and notice that there is corrosion, damage, or obvious issues with the device itself, it may need to be replaced if a reset does not work.

How to Reset Bradford White Water Heater Thermostat Well Sensor Fault

Man fixing the water heater

If you own a Bradford White water heater, you should be able to have access to hot water that has been set to the temperature you most often desire. Even if you have your water heater set to its hotting temperature, the water should never go over a certain temperature in order to protect individuals from being scaled and to monitor this, there is the well sensor. If you see a message that is indicating a well sensor fault in your water heater, how can it be reset?

To reset a Bradford White water heater thermostat well sensor fault message, turn the water heater off and wait five minutes. Turn the knob to ‘Pilot Mode,’ hold the knob down, simultaneously press the button below it until a click is heard, then wait for the ‘Status’ light to blink green.

The important thing to remember in this instance is that the water heater thermostat well sensor has been put in place to notify owners when the temperature of the water has reached to high a level. If you know that the water temperature is correct, then resetting the sensor is the right option. However, if there is an issue with the water getting too hot, resetting the sensor will not resolve the problem and further inspection of the sensor should be made.

How to Reset Bradford White Water Heater Pilot Light

Man fixing the water heater

The pilot light of a Bradford White water heater is one of the most essential components to getting hot water and having it whenever is needed as the pilot light must be lit in order to heat a larger heating element within the water heater so that hot water is readily available. If the pilot light is not igniting, is not staying lit, or will not light at all, a reset can be performed to restore the operation of this component, but what does the process look like?

To reset a Bradford White water heater, turn the heater off and allow gas to disperse for five minutes. You will then turn the knob to ‘Pilot Mode,’ continue holding it down, press the button directly beneath the knob until you hear it click, then wait for the ‘Status’ light to flash green.

When you see that the status light has turned green, you will then turn the knob to ‘Hot’ in which you should be able to hear the pilot light ignite, indicating that the reset was successful and the pilot light is operating as it should. If you do not hear the pilot light ignite, be sure that the gas valve has no damage or corrosion and that it is able to open easily, as a defective gas valve may be the source of the problems you are experiencing rather than the pilot light itself.

How to Reset Bradford White Water Heater Flammable Vapor Sensor

Man fixing the water heater

The flammable vapor sensor on a Bradford White water heater is one component that gets little daily recognition, but one that works tirelessly to protect those in ownership of such a plumbing fixture. The vapor sensor on a Bradford White water heater is able to detect fumes that are capable of ignition and when this happens, the water heater shuts off and will not run until those fumes have been cleared. If you need to reset this component though, how can it be done?

To reset a Bradford White water heater flammable vapor sensor, turn the pilot light off and turn the knob to the hottest setting. You will then turn the knob to the vacation setting. When done once, repeat the last two steps six more times and once done, the flammable vapor sensor will reset.

This component of your Bradford White water heater may not be something you think of as often as the pilot light, but if the flammable vapor sensor keeps going off and you can’t seem to find a reason for this to happen, you need to make certain that there are no leaks within your home or business that may be tripping the sensor. If there is a leak somewhere, this can be incredibly dangerous when it comes in contact with the open pilot light and should be repaired immediately.

To reset a Bradford White water heater, turn the heater off and allow five minutes for all gas to escape. You will then turn the knob to ‘Pilot Mode,’ continue to hold the knob, and press the red button directly below the knob until a click can be heard and the ‘Status’ Light flashes green.

Related Articles

Bradford White Water Heater Noise Problem

Bradford White Water Heater Heating Problem

Bradford White Water Heater Not Working

ReadyToDIY is the owner of this article. This post was published on May 5, 2022.

Bradford White Water Heater Blinking What It Means