You can install laminate flooring on walls that are non-sloping and climate-controlled. The tape and caulk adhesive methods are most common because they don’t require as many nails. Clean the walls, pry up the trim, and add the laminate flooring row by row.
We all want to be proud of our home so from the floor to the ceiling, we want everything to be just right. Surprisingly, one …
One of the most important home decorating decisions is associated with flooring. Certain styles of flooring have come in and out of favor over the …
Laying tile over vinyl flooring is possible if the resilient flooring is in good condition and glued on a sturdy subfloor. If your vinyl flooring is too high or made of luxury vinyl planks, you will have to remove it before applying tiles. The vinyl must be clean and intact before tiling it.
There are 3 broad steps to laying vinyl flooring over plywood: preparing the plywood surface, laying the vinyl flooring down, and finishing the vinyl – if required. Vinyl flooring can either be purchased as tiles which are laid individually, or as one big sheet.
Installing laminate on uneven concrete subflooring will make the planks lose and shorten their lifespan. If the concrete flooring has dips and hills, you need to correct it using a grinder and leveling agent. Once the subfloor is even, apply a vapor barrier underlayment to remedy any imperfection.
You can’t install carpet on uneven flooring because an uneven subfloor will cause the carpet to receive uneven weight. This will only intensify wear and tear damage. Prior to installing the carpet, the subflooring has to be prepared to optimize the longevity of the flooring and prevent damage.
When it comes to preparation before installing vinyl floors over laminate flooring, the most important step you can take is cleaning the surface of the particle board. To do this, you will need to thoroughly vacuum the area to make sure that no dust or other debris remains once you have gone over the entire surface.
The most important aspect of preparation is to ensure that the particle board has been properly cleaned. This means that there should be as little dust and debris as possible on the surface. Once the surface has been thoroughly cleaned, you will then need to ensure that the floor is level. If the space is not level, it can cause problems with the initial installation or problems later on for your vinyl plank flooring.
To remove floor tiles without underfloor heating, use a putty knife and pry bar to loosen the tiles, remove the molding, get rid of the grout, and use a hammer drill to break the tile. If the area has underfloor heating, use a sander to remove the adhesive gently to reach the subfloor.
Linoleum can be installed over any floor, including hardwood, provided it has been prepared properly. This involves making the surface flat, dry, level and smooth by sanding and levelling the wood, vacuuming and tightening nails/screws. This can also be achieved by using an underlayment instead.
If no underlayment is beneath the tiles or panels of your floating floor, you will need to install a separate underlayment above your hardwood floors. Underlayment helps to take out any major deviations that may be on your hardwood, helps to muffle noise when in use, and also helps to support the floating floor above it. Simply purchase the underlayment, install it on top of your hardwood, then lay your floating floors above.
Heated flooring can be used with any vinyl floor covering, including vinyl planks, tiles and sheets. Vinyl planks are more versatile and can be laid directly on top of thin floor wiring, whereas adhesive vinyl tiles and sheets can only be laid over wires that are embedded within a cement layer.
Concrete is one of the preferred surfaces for peel and stick tiles. It provides a suitably flat surface, and the tiles will stick well if the concrete has been prepared correctly. This includes removing dirt and debris, plugging holes and cracks, levelling the concrete and priming the surface.
While it is possible to install vinyl plank flooring under cabinets, it is not recommended. Vinyl will expand and contract with temperature variations, causing the entire floor to buckle if pinned under cabinets. However, installing it under appliances is safe because they are not fixed in place.
To keep your porcelain or ceramic tile as clean as possible, as previously discussed, the grout that you use for your tile needs to be sealed. There are various types of seals out there, but choose one that fits the needs of the space, but that will also keep the most stains from penetrating the surface. The tiles (for most) have no need to be sealed, as this is completed when manufactured to ensure that they are stain-resistant.
When transporting vinyl sheets, you want to be sure to keep the material upright and on its ends to ensure that no damage is done to the surface of the material. Once you have it transported to where it is going, you will need to store it in a controlled temperature environment that is no cooler than 65 degrees Fahrenheit and no hotter than 80 degrees Fahrenheit.
Generally speaking, transition strips are used to make the transition from one floor to another. It may help to make a smooth transition from one height to another or from one type of floor to another. A properly installed transition strip also adds to the safety of the home, because it reduces or eliminates a tripping hazard.
The process of installing vinyl plank flooring is fairly straightforward. After you establish your first row, you continue to move across the room, pushing the …
As a whole OSB is not the best option to use as an underlayment for engineered hardwood, and the main reason is that it puffs up when it comes into contact with water, and doesn’t shrink back again. Plywood will shrink back to its original shape after it expands.
As a general rule you should always level the floor first using a levelling compound. It is much easier to apply the adhesive when the floor is already level. When the floor is uneven it’s more difficult to get the groove patterns you need in the adhesive.
Your floor can probably support tile, but in rare cases, it depends on the type of subflooring in your home, the amount, strength, and size of your floor joists, and whether you’re tiling a first-level or upper-level floor of your home. Tile weighs about 4-6 pounds per square foot.
You can lay tile over painted concrete floors, but the adhesive isn’t always reliable. If you choose to try anyway, remove the paint, grind the concrete, or resurface the floor first to ensure that the adhesive holds. This requires sanding, power washing, paint strippers, or soda blasting.
If your ceramic floor tiles aren’t sticking, it could be due to improperly mixed grout/thinset or not using enough grout/thinset. You could also be attaching the tiles to the wrong base, letting the thinset become too dry before applying the tiles, etc. Determining the problem is key to fixing it.
There are many things you could do to spruce up a home but if you want to take things to the next level, installing a …
Installing carpeting directly over a laminate floor is an option that can easily be done. If the existing laminate floor is in good shape, you can install the carpeting and live on it for many years. When you remove the carpeting, you may even be able to salvage the laminate flooring.
You can tile over your old floor adhesive by placing a barrier down in the form of thin-set, underlayment, a false floor, or using a floor leveling compound before tile installation. To achieve the strongest bond and preserve your moisture barrier, you should scrape, sand, or strip the old adhesive.
Laminate can be installed on an uneven floor; however this can degrade the quality of your new laminate. The finished product may become warped as a result, causing the floor to shift and become damaged when walked on. For this reason, it is best to level the subfloor prior to installing laminate.
You can install Luxury Vinyl Plank (LVP) or laminate wood flooring directly over carpet with low pile height. Flooring professionals do not recommend the long-term installation of laminate or LVP over high pile carpet. You can secure plywood on top of plush carpeting to achieve stability in a pinch.
You can definitely install carpet over the existing hardwood floors in your home. A substantial amount of time and energy will be required to undertake this project properly. You may want to consider going through a flooring professional to avoid potentially damaging your original hardwood floor.
Installing vinyl plank over ceramic tile makes a great choice because of its cost-effectiveness and stylish look. Vinyl flooring resists scratches, mold, mildew and stains. …
Putting a tile floor over an engineered wood floor is possible only if you prepare the subfloor properly. The engineered wood will become the subfloor. As long as it is secured in place and does not have any flaws in it, the tile can be put over it successfully.
There is nothing quite like the beauty of a solid hardwood floor. Many floors also have their own beauty, including title and even carpet. If …
Although a tile floor has a beautiful appeal, there are many reasons why you might consider making the transition to carpet. Carpet provides insulation under …
When you remove linoleum from a hardwood floor properly you can do so without damaging the floor underneath. It takes time and effort but it can be done successfully. As long as you follow some practical safety guidelines, you can also remove the linoleum without harming your health.