Maytag washers are commonly known as one of the market’s most efficient and dependable home appliances. Although these reliable washers last for several years and clean many dirty laundry loads, there will always be occasions when these complicated appliances do not function as expected.
If your Maytag washer keeps filling with water, the issue may be with the water inlet valve. If this valve is faulty or stuck open, it will continue to allow water into the machine. Replacing or repairing the water inlet valve should resolve this issue.
Another potential cause is a malfunctioning pressure switch. This switch tells your washer when to stop filling with water based on the water level. If it’s not working correctly, the washer may overfill. Check the pressure switch and the hose connected to it for any clogs or damage, and replace if necessary.
Finally, a blocked or kinked drain hose could also cause continuous filling. If the hose is not positioned correctly or is obstructed, water might not be draining properly, misleading the washer to keep filling. Ensure the drain hose is properly aligned and free from any blockages.
Throughout this article, you’ll also learn the following info:
- What to check if your Maytag washer is having issues filling up with water, won’t fill up completely, or keeps filling non-stop
- Common causes and quick solutions
- How you can maintain your Maytag washer so it functions properly
Maytag Washer Won’t Fill Up at All
If your Maytag washer is not filling, you might need to check the washer hoses, the water supply, the water inlet hose/valve. You should also verify that you installed your washer per the Maytag washer manual for optimal performance.
Check the Washer Hose
Your Maytag washer needs to be attached to both the hot and cold water supply lines. If there is only one supply line of water, then the machine will not function properly. For the appliance to complete a wash cycle, the water valve needs the water pressure from both lines to complete a cleaning cycle.
Check the Water Inlet Valve and Water Inlet Hose
There are filter screens designed to collect sediment and debris from the water in each water inlet valve before it flows into the washer. If these filter screens are clogged, then water from one or both inlet valves cannot fill the washer.
Switch off the water supply line and detach the hose from behind the appliance to inspect these filters. If there is any debris, then gently clean it off with mild soap and water. If the bits clogging the filter is particularly stubborn, use a soft toothbrush to brush the sediment off the screen.
After cleaning off the debris, reattach the hoses and slowly turn on the water supply while checking for any water leaks at the water inlet valve. Maytag recommends that you should replace the fill hoses approximately every five years to maintain quality washer performance.
Check the Drain Hose Installation
Verify that the drain hose in the pipe is not installed too deep, as improper installation can cause water to siphon and not fill the Samsung washer to the appropriate water level. If the drain hose is installed too deep, it can also cause water to drain back up into the washer tub or slow down the spinning of your washer’s cleaning cycle.
You should also check for any kinks in the water inlet hose as any bends can slow or limit the water flow. The drain hose needs to be in a U-shape, as stated in Maytag’s washer installation instructions.
Maytag Washer Won’t Fill Up Completely
If your Maytag machine does not fill up with water, it may be due to the washer’s feature rather than a problem with your device. Depending on the model, Maytag washers can sense the laundry load’s weight and fill the washer with an appropriate water level for a cleaning cycle.
Adding more water to the cleaning cycle can cause the laundry to float and decrease your washer’s cleaning power. Selecting the washer’s Heavy Duty or Bulky washing cycle will fill the washer with more water than the energy-efficient cleaning options.
While you might think that the washer needs to fill with water to engage in a wash cycle, this is unnecessary as having the clothes entirely submerged in water will make it difficult for the clothes to move. Not only does the volume of water vary with load size, but it also differs depending on the cleaning cycle you select.
Depending on your Maytag washer, the water level might seem low if it is a machine that consumes a lower amount of water than other washer models available on the consumer market. In this case, your Maytag washer’s water depth will not be as noticeable when compared to a standard deep fill washing machine.
Copyright protected content owner: ReadyToDIY.com and was initially posted on November 26, 2020.
Additionally, some Maytag washer models will fill from the top, while other models will fill water from the bottom. If the washer fills from the bottom, then the appliance’s water volume may be less apparent during the water filling mode.
Re-Calibrate the Washer
However, you might feel like the water level is much less than when you first bought and installed the washer at your home. Try running a Clean Washer cycle as it re-calibrates the control and resets it back to the factory’s water levels. You should maintain your Maytag washer’s performance by running the wash cycle at minimum one time a month, as this will calibrate your Maytag washer.
Maytag Washer Keeps Filling Non-Stop
If your washer continuously fills up with water non-stop, you can do a simple test to figure out which component is malfunctioning. It can be your water inlet valve, pressure switch, or even your household’s water pressure.
Check the Water Inlet Valve
Try cutting off power to the washer as it fills up with water. If the water level in the washer continues to rise as the appliance does not receive any electricity, then the water inlet valve is malfunctioning. You will need to replace it.
Check the Pressure Switch
When your Maytag washer senses that there is enough water in your machine, the pressure switch cuts off power from the water inlet valve. If the pressure switch in your washer malfunctions, then it cannot sense that there is enough water in the washer tub.
Copyright article owner is ReadyToDiy.com for this article. This post was first published on November 26, 2020.
This faulty mechanism causes the Samsung washer to fill non-stop and eventually may cause the machine to overflow with water. You should also check the air tube on the pressure switch to ensure that it is not leaking and is clean of any debris.
Maytag Washer Error Codes
If you see the “LF” or “F8E1” error code displayed on your washer, then it means that the washer is either taking too long to fill with the necessary amount of water or the washer keeps filling and draining the water within the tub. These issues indicate that there may be an issue with the supply of water flow. Check your washer’s owner manual for proper installation instructions.
Maytag notes that you should not tape over the drain’s opening and ensure that the drain hose only extends approximately 4.5 inches (114 millimeters) into the standpipe. These issues can cause the appliance to drain and fill simultaneously, which can make water not load the machine to the level necessary to run a cleaning cycle.
Call a Maytag Authorized Service Technician
More complicated issues may require an authorized service technician to take a look at your Maytag washer. If you continue to have problems, you should sign up and register your Maytag washing machine at the Maytag Owner Support Center. After registering your appliance, you can then review your warranty information and schedule a repair service.
Final Thoughts
Maytag washers are widely regarded as some of the most durable home appliances on the market. However, these complicated machines can eventually run into some problems.
Inspect your washer for potential issues such as incorrect installation or malfunctioning parts that become defective from continuous usage. While you can quickly troubleshoot and fix some parts of your machine, more complicated issues will require your washer to be serviced or replaced by an authorized technician.
Related Articles
Maytag Washer Sensing Light Blinking
Maytag Washer Making Loud Noise During Spin
My Maytag Washer Won’t Work: How to Fix
ReadyToDIY is the owner of this article. This post was published on November 26, 2020.