As a general rule, the tub can’t drain the water that’s in it due to clog, or the tub is out of balance. It’s common for the tub to go out of balance, and you should adjust heavy items in the tub to spread them out. Otherwise, do the steps below to identify why it’s happening.
Overall, water is not entering the tub, or water is draining from the tub as it’s filling. Restart your Amana washer first by taking the power plug out at the wall for 10 seconds, and then plug it back in again. If it still has a sensing fill issue refer to the steps below.
In general, there is no water entering the tub, the tub can’t drain, or the control panel has malfunctioned. First, restart your Amana washer by unplugging it from the wall for 30 seconds, and then plugging it in again. If the lights still flash, then refer to the troubleshooting steps below.
In general, if nothing is happening there is an issue with the water filling the tub or draining from the tub. But, if the wash light is on and you can hear your Amana washer doing something, it means it’s in the wash part of the wash cycle. Below is what to do if your washer is not doing anything.
A common reason why a Whirlpool electric heater is not heating is due to a faulty thermal fuse. The thermal fuse measures the heat in the dryer and turns off the heater if high temperatures are detected. When the thermal fuse is going bad, it may send inappropriate signals to the main controller.
If your Maytag washer is not spinning the first thing to check is the cycle settings. You may have set it on a delicate setting or hand wash, which does not include a heavy-duty spin cycle. In addition, you may have turned off the spin cycle directly.
One issue that can lead to a Whirlpool washer not spinning quickly is that the water level switch is not operating properly. If the water level switch is clogged, it will not allow pressure to get to the sensor and it can keep the machine from spinning as quickly as it should.
In general, start by restarting your smartphone, GE washer, and your WiFi router. Attempt to connect your GE washer over the SmartHQ app again. If it still won’t connect then connect it over Bluetooth by adding it as a Bluetooth device. When it still won’t connect then do the steps below.
Overall, your Bosch washer needs to be put in drum clean mode because it’s due for a routine drum clean, the onboard computer has malfunctioned and you need to restart your Bosch washer. But, there can also be an error code showing on the LCD display, which you can look up in your owner’s manual.
Remove the rear panel to locate the lid switch to bypass an LG washer lid lock. Place a magnet between the lid switch and the appliance to achieve a magnetic connection. Lower the lid and plug the washer back. Turn the washer on, lift the lid and run a washing cycle.
If your Samsung washer won’t fill or keeps filling, it may be because of a bent water supply line, low water pressure, a broken water level switch, a broken water inlet valve, or a broken main control board. Contact an expert to check these components for any issues and replace them if necessary.
A GE washer may beep and not start for a number of reasons but the most common reason is a faulty door sensor. If the door sensor is failing or broken, it will signal the control board that the door is open and it will not start for safety reasons. You can replace the door sensor along with the latch.
In general, the laundry is out of balance and needs to be adjusted so that it’s evenly distributed. The following are also issues that can cause this to happen, it’s overloaded with heavy items, or too much laundry, your Bosch washer is not level, or the belt or actuator has failed.
As a general rule, the filters where the water supply lines connect to your washer need to be cleaned, the taps that supply water aren’t turned on all the way, or aren’t supplying water, there is a kink in the water supply lines, the door is broken, or the pressure switch is broken.
As a general rule, the drain filter is clogged and needs to be cleared, the drain hose has a kink or a blockage, your Bosch washer needs to be restarted, the drain pump has failed and needs to be replaced, or the drain pump has something like a child’s sock stuck in it.
In general, first check the wall outlet is supplying power. If it is then the internal computer can be faulty and your Bosch washer needs to be restarted, the door switch isn’t closed completely or it’s faulty, the power cord is faulty, or the control board has failed and needs to be replaced.
Overall, your Bosch washer needs to be restarted, The child lock is on, the door mechanism is almost broken and is stuck, the door mechanism has failed, the internal computer is faulty and won’t release the lock, or your washer won’t drain and so the computer won’t allow the door to open.
If the lid is not closed properly, the GE washer will not spin. This is a safety feature that is built into the washing machine to protect you and your family from harm. On the other hand, if the lid is closed but the lid switch is faulty, it will signal to the control board that the lid is open.
To resolve the problem, inspect the above components to repair or replace the defective ones. Replace the affected areas with genuine parts to prevent the problem from recurring. Some of the above areas may require careful attention. Don’t attempt to repair the washer if you aren’t good at the job.
To avoid your clothes smelling, it is recommended by Samsung that you put the washer on a self-clean cycle every 20 – 40 washes. That means the average household should clean their washer at least once a month. But it can be more often If the washer is used more often than once every 2 or 3 days.
The most common reason for a Samsung washer to not drain properly is a blocked drain pipe. After that, the drain filter or drain pump could be the cause of water standing in the machine. Occasionally, the drain hose will not be at the correct height, preventing the water from draining properly.
If a Samsung washer fuse is blown, you’ll need to remove the access panel on the back of the machine. The main logic board is located right at the bottom of the machine and is held in place by two screws and two plastic clips. The fuse is located on the logic board.
Overall, the agitator is loose and needs to be tightened or replaced, it’s overloaded with too many heavy items, or too much laundry, the washer is not level because one of the feet are too long or too short, or the stabilizers on the side of the tub have failed and need to be replaced.
Overall, the drain pump has a clog in it, the drain pump has failed, the onboard computer needs to be restarted by unplugging your GE washer and the wall and plugging it back in again, or the drain hose is kinked or is not installed into the stand pipe correctly.
You can bypass the Amana washer lid lock in just a few steps, but it’s important that you plan it well and do it properly. If you fail the bypass, your machine won’t turn on, and it might not work properly again. Take bypassing the washer lid lock seriously.
To fix the oily smell, run an empty hot water cycle with white vinegar to remove any oil/ grease accumulation on the washer tub and the drains. Also, dip a towel in a vinegar and baking soda solution and then use it to wipe any layers of oil on the door seal.
To fix GE washer smells, use the hot cycle regularly. Also, leave the door open after use, to allow the inside to dry out. Make sure that the door seal is cleaned regularly with bleach or white vinegar. Check the drain pump and filter and remove any obstructions that prevent the water from draining.
Your GE washer lid lock is not working due to mechanical or electrical failure. Examine the door lock for any damaGE and replace it if it’s damaged. Test the door switches and replace any that lack continuity. Further, examine the door strike and main control board and replace any damaged parts.
The most common cause of a back leak in an Electrolux washer is a damaged drain or water inlet hose. If you observe the washer leaking when it is in the spin cycle, it is another indication that a hose may be the cause of the leak. To fix the problem, check the inlet hose connection at the tap.
You can bypass the lid lock on a Maytag washing machine by splicing a switch into the locking mechanism wiring. To do this, you need to remove the lock mechanism and disconnect the wiring. Remove the three wires from the lock and connect them to an AC switch.
The Electrolux washer is a very dependable washing machine made for frequent and heavy use. However, there may be times when you may experience issues with the washer not draining properly. The solutions to these common issues are easy to determine and can be corrected with minimal effort. The Electrolux washer should then continue draining in the usual efficient manner.
When you have Electrolux washer starting problems, it is likely an issue with the power. Check the receptacle and make sure that the circuit breakers have not tripped. Otherwise, it could be a line fuse or thermal fuse that is keeping the washer from starting.
We depend upon our Electrolux washing machines to get the job done each and every day. When they are not working properly, it can be …
A Kenmore washer lid lock can stop working either due to mechanical or electrical hitches. Inspect the lid lock for damage, and other parts such as the door latch, motor or switch assembly, door strike, the switch, and the main control board. If you find a defect in any of the parts, replace it.
Admiral washers have a safety feature that stops it from being opened when it’s agitating and spinning. In rare cases this small mechanism can fail …