Skip to Content

How to Clean Dyson Vacuum

Having clean carpets in your home is, of course, an essential part of keeping your family healthy and it is best to do this on a routine basis. If you want to keep this routine going, it is crucial that you clean your Dyson Vacuum often and correctly. This will help to avoid the buildup of dirt and debris which can cause it to fail to work efficiently or even to stop working entirely. Read on to learn more about the best techniques to clean your Dyson Vacuum to ensure its maximum efficiency.

If you want to know how to clean your Dyson Vacuum, you will need to use an air compressor and scissors or a knife. Use the scissors or knife to cut out any clumps of hair on the roller, canister, or vacuum unit.

Woman cleaning the floor using vacuum

Now, use the air compressor to blow out any areas of trapped dust or dirt throughout the entire vacuum, including the canister.   

Then, take off the outer shell of the vacuum canister. You can do this by pressing on the button that you will see located on the back of the canister that is in the middle between 2 red plastic pieces.

Now, take out the Foam Filter by opening the flap on the bottom of the vacuum canister. Go ahead and leave this aside.

Take the Roller Cover off by first putting the vacuum cleaner upside down. Then, use a flathead screwdriver to take the bottom roller cover off.

Take the main part of the Dyson Vacuum Cleaner and, holding it over a large garbage can, use your compressed air apparatus to blow out all small holes both on the inside and on the outside of the unit.

Now, take the sponge filter and the canister and run it under the water source. Keep squeezing the sponge filter until such time as all the water expelled from it is running clear.

Then, run water through the canister as well. Use mild dish detergent with a scrub brush to clean the canister carefully and fully.

Now, use a paper towel to ensure that all the small holes are free of blockages.

Put all the component pieces of your Dyson Vacuum out in a dry place for at least twenty-four hours.

How to Clean a Dyson Vacuum Canister

Woman cleaning the floor using vacuum

It is a relatively simple process to clean your Dyson Vacuum Canister as discussed below.       

If you want to know how to clean your Dyson Vacuum Cleaner and you want to know how to clean your Dyson Vacuum Canister, empty all debris out of the canister. Then, run water through the canister to rinse it completely. Finally, use dish soap to clean the canister and then use a towel to dry it.

Now, take off the Roller Cover.  Run the sponge under cool water and then squeeze it out until the water runs clear.

Make sure the Dyson Vacuum Cleaner Cannister is entirely dry by leaving it in a dry place for at least twenty-four hours. By doing this, you will be able to avoid any clumping of dirt in the small holes  

How to Clean a Dyson Vacuum Cleaner Filter

Woman cleaning the floor using vacuum

Cleaning your Dyson Vacuum Filter can be easily accomplished by following the steps as outlined below.

If you want to know how to clean your Dyson Vacuum and you want to know how to clean the Dyson Vacuum Cleaner Filter, turn your vacuum cleaner off and disconnect it from the wall socket. Take out all the Dyson Filters. Use cold water to rinse off the filters while rubbing them using your hands.

Make sure that before you rinse the filters off with water, that you carefully remove any excess dust, any excess dirt, or any accumulated debris that you may find on the Dyson vacuum filter. Gently tap the filters on either the sink edge or on the side of the bin to take off any excess dirt or any grime or any other excessive types of debris.

Keep rinsing the filters with running cold water and keep doing this until all the water runs clear. Then carefully squeeze out all the water from each of the filters.

Then dry the filters for a period of at least twenty-four hours where there is adequate airflow to allow for efficient drying of the filters. You can also try to leave the drying filters in front of a fan or in front of an open window. It is essential not to replace the filters until they are completely dry, or you could risk causing damage to the Dyson Vacuum Motor. Before you replace the filters, test using your fingers to make sure that the vacuum filter has not retained any residual moisture. Now, replace all the clean filters.

How to Clean a Dyson Vacuum Cleaner Hose

Woman cleaning the floor using vacuum

If your Dyson Vacuum Cleaner Hose is clogged and needs to be cleaned, you can carefully check for any blockages since this will greatly affect the suction power of the vacuum. Failure to do this can cause damage to the vacuum cleaner motor.  Follow the steps as outlined below to resolve this problem by cleaning out the Dyson Vacuum Cleaner hose.

If you want to know how to clean your Dyson Vacuum Cleaner and you want to know how to clean the hose of your Dyson Vacuum Cleaner, first remove with your hands whatever debris in the hose that you can easily see and reach and then use a broomstick to reach further to clean out any remaining debris.

When the hose is clear of debris, you can use a small and damp cloth that you can push through the vacuum cleaner hose with the same broomstick used before.

In this way, you will be able to remove any dirt or dust particles that are adhered to the walls of the vacuum cleaner hose that otherwise will remain behind.

Be sure to allow for at least twenty-four hours for the hose to fully dry before you try to attach it again to the vacuum cleaner body.

If you fail to allow the vacuum cleaner hose to fully dry, you risk the development of mold which will then contaminate the entire vacuum, rendering it unusable.

How to Clean a Dyson Vacuum Roller

Woman cleaning the floor using vacuum

Dyson vacuums currently have roller brushes that are now fully motorized. Because of this, however, there is a large risk of pet hair and other debris and residues getting stuck to and tangled in the vacuum rollers.

If you want to know how to clean a Dyson Vacuum and you also want to know how to clean a Dyson Vacuum Roller, unclip the vacuum tube from the roller brush. Then unlock the vacuum roller and remove it from its housing. Now, clean the roller carefully using your hands to take off any dirt.

Now, clean the outer shell of the Roller with a dry cloth.

If necessary, you can add a small amount of water to remove particles of dirt and debris that are embedded with it.

Copyright protected content owner: ReadyToDIY.com and was initially posted on February 27, 2022.

If you do this, be sure not to wet the inside of the vacuum roller brush which is run by a motor and which is connected to the vacuum’s motor.

The roller brush needs to be completely dry before you reassemble the entire unit.

How to Clean Dyson Vacuum Brush Head

Woman cleaning the floor using vacuum

If you need to clean your Dyson Vacuum Brush Head, it can be done quickly and is normally not a very complicated process.

If you want to know how to clean your Dyson Vacuum and you want to know how to clean your Dyson Vacuum Brush Head, first, pull the end cap away from the brush bar. Rotate the end cap to unlock it and then take it off. Now, wash off the soft roller head with cool, clean water from the tap.

Then, let the soft roller head dry for an entire day.

Reattach the end cap back on to the large brush bar. Put the Soft Roller Cleaner Head back onto its attachment and lock the fastener back in place.

How to Clean Dyson Vacuum Cleaner Brush

Woman cleaning the floor using vacuum

It is very important to periodically clean your Dyson Vacuum Cleaner Brush at least every three months. To do so, follow the instructions as outlined below.

If you want to know how to clean your Dyson Vacuum Cleaner and want to know how to clean your Dyson Vacuum Cleaner Brush, first remove the wand by pressing the red catch release button and then simply pull the cleaner brush off from the vacuum cleaner head. Then, empty all the dust and other debris from the brush out into a trash receptacle.

Make sure to never put the cleaner brush into either a dishwasher or into a washing machine and only use cold water to clean it. Also, never use any detergents to clean the vacuum cleaner brush.

How to Clean Dyson Vacuum Motor

Woman cleaning the floor using vacuum

If your Dyson Vacuum Cleaner has stopped working, it may require a cleaning of the Dyson Vacuum Cleaner Motor in a final attempt to avoid having to replace it. Read on to learn how to clean your Dyson Vacuum Cleaner Motor quickly and efficiently.

If you want to learn how to clean your Dyson Vacuum Cleaner and you want to learn how to clean your Dyson Vacuum Cleaner Motor, first, disconnect the vacuum from its power source. Now, take the wand and motor head off and then remove the bin.

Now, undo the screw on the back of the vacuum cleaner body to take the motor off to begin the motor cleaning process.

Take the motor apart per the instructions in your Dyson Vacuum Owner’s Manual and then begin the cleaning process.

How to Clean Dyson Vacuum Wheels

Woman cleaning the floor using vacuum

The small plastic wheels on a Dyson Vacuum tend to get obstructed by hair strands which often must be removed. Sometimes, dirt and other debris also gets jammed between the wheels and the axle. You can do this by carefully disassembling the wheel units.

If you want to know how to clean your Dyson Vacuum and you want to know how to clean the Dyson Vacuum Wheels, be sure to carefully remove the metal pegs that hold the wheels in. When the wheels are fully removed, take the pegs out.

You can usually get the pegs off by gently using a Claw Hammer or by using a Punch. Now, go ahead and clean the wheels off. You will usually need to cut off all of the embedded hair strands and remove all of the hair that is stuck in the pin.

Try using a very small needle nose pliers to clean the four small wheels that are in each corner. These wheels are usually the hardest ones to clean.  It is often exceedingly difficult to clean the wheels that are in the center area.

You can use the same needle nose pliers to pry up one end of the wheel axle so that you can pull it easily out of the wheel.

In addition, you can use a flat head screwdriver under the pin that you can see in the area between the wheel and the main plastic area, to pry the wheel off.

After you clean the wheels significantly, you will need to replace them carefully by using the flathead screwdriver. Take it and apply low pressure but steady downward force on the pins so that they snap into place easily.

Copyright article owner is ReadyToDiy.com for this article. This post was first published on February 27, 2022.

Do not exert excessive pressure as you may inadvertently snap the pins in half.

Related Articles

Dyson Vacuum Overheating/Cutting Off/Blowing Fuse

Dyson Red/Blue/Green/Orange Light Flashing/On

Can Dyson Vacuum Water, Sand, Food, Glass, Dust, etc.?

How to Reset Dyson Vacuum

ReadyToDIY is the owner of this article. This post was published on February 27, 2022.

Dyson Cordless Vacuum Battery Problems