There are plenty of video doorbells on the market, but Arlo seems to have nailed it as far as their build quality and high-resolution images are concerned.
While installing the doorbell is straightforward, there are times that you may need to reset your Arlo doorbell due to network problems or after a firmware upgrade.
You can reset your doorbell by using the cell phone app or you can remove the doorbell from its bracket and manually reset it.
To reset an Arlo doorbell, push and hold the reset button for 10 seconds. You can find the reset button on the rear of the case. To indicate that the reset process is in progress, the LED ring on the front flashes white. Once the doorbell is reset, you need to add it to your account again.
You’ll need a release pin or paper clip to push the reset button as it is hidden inside a deep hole in the rear of the doorbell case.
To gain access to the back of the doorbell, you have to push the pinhole release button at the top of the doorbell mount. This will allow you to tilt and lift the doorbell off of its mounting bracket.
Resetting the doorbell removes your doorbell from your Arlo account, so you have to log onto the website or access your cell phone app.
On the device’s screen, you must select “Add a New Device”. You must scroll to the bottom of the screen to find the option. Next, select the Arlo Video Doorbell setup option and follow the instructions that appear on-screen.
Where is the Reset Button on Arlo Video Doorbell?
If you are new to setting up the Arlo video doorbell, then it can be a little difficult to find the reset button.
Some doorbells have a hidden reset button that requires a pin and others have a sync button that is located in between the batteries.
To find the reset button on your Arlo Video Doorbell, you have to remove the unit from the door frame or mounting location to gain access to the rear panel on the case. The doorbell has a pinhole release located at the top of the mount. Lift the doorbell out of the mount by tilting it forward.
You need to use a paper clip or other sharp object to push the release clip.
Once the doorbell is free from the mounting bracket, you can turn it over and locate the reset button at the top of the rear case recess.
You can use the same paper clip or pin to push the reset button once you have located the hole.
How to Factory Reset Arlo Wireless Doorbell
The Arlo wireless doorbell is reasonably quick and easy to set up. However, you need to follow a few steps to reset the doorbell.
To factory reset an Arlo wireless doorbell requires the removal of the doorbell from its mounting bracket. Using a release pin or paper clip, locate the release hole on top of the doorbell bracket and press it. Remove the doorbell and push the reset button located on the back of the case.
You’ll need to press the reset button for about 10 seconds before the white LED lights on the front of the doorbell start to flash.
The flashing white LEDs indicate that the factory reset is in progress and you have to set up your doorbell on your account.
The factory reset process removes the doorbell from your account automatically.
You can set up your doorbell via the website or through your phone app.
If you don’t wish to remove the doorbell from its mounting bracket to reset it, you can do the factory reset from the app.
[This article and its contents are owned by Ready To DIY and was first published on 05/26/2022]
With the doorbell connected to AC power and connected online to your WiFi network, go to device settings in the app. Select “Remove Device” and the doorbell will reset to the default factory settings.
How Do I Reset My Arlo Video Doorbell?
The process for resetting your Arlo video doorbell is quite straightforward.
It can be a bit confusing if you are unfamiliar with the mounting bracket as the doorbell has to be removed before you can reset the unit.
To reset an Arlo video doorbell, locate the release-pin hole on the top of the mounting bracket. Using a pin or a paper clip, push the release clip in and once it snaps open, tilt the unit and lift it out. Insert a pin in the hole in the back of the unit and press the reset button for 10 seconds.
Be careful when you remove the doorbell from its bracket as the unit tilts forward slightly before lifting straight up and out.
After pressing the reset button, you’ll have to wait for about 10 seconds before the LED lights on the front of the doorbell start to flash white.
The flashing white lights show that the factory reset has been completed and your doorbell has been removed from your account.
Log into your Arlo account and set up your doorbell again by following the on-screen instructions.
How to Factory Reset Arlo Audio Doorbell
Factory resetting the Arlo audio doorbell follows a similar procedure to the video unit.
Copyright protected content owner: ReadyToDIY.com and was initially posted on May 26, 2022.
To factory reset the Arlo audio doorbell, unscrew the retaining screw on the bottom of the mounting bracket and slide the doorbell out. Press and hold the sync button for about 10 seconds. The light will flash white repeatedly to show that the factory reset is successful.
The difference in mounting bracket retaining screw position can be confusing if you’re used to the Arlo video doorbell.
You’ll need a small Phillips head screwdriver to unscrew the retaining screw.
Once the screw is out, the doorbell easily lifts up and out.
After removing the battery cover, leave the batteries in place and push the sync button that is located in the middle between the two batteries.
Don’t remove the batteries, otherwise, the factory reset will not proceed.
How to Reset Arlo Doorbell Camera
When you reset your Arlo doorbell camera, the unit is returned to its original factory settings.
To reset an Arlo doorbell camera, insert a pin into the release hole in the mounting bracket. Slide the doorbell unit out and locate the reset button hole in the back of the case. Push the reset button with a pin or paper clip for 10 seconds. When the LEDs flash white, the unit is reset.
Be careful when you remove the doorbell from its mounting bracket. You must tilt it forward slightly and then lift it out vertically otherwise you risk damaging the bracket.
Once the LED lights flash white, the unit will be reset to the original factory settings and removed from your list of doorbells in your account.
You’ll have to log onto the website or use the cell phone app to set the doorbell up on your account.
You can also factory reset your doorbell camera via the app. Just remove it from the app using the settings menu.
What to Do if Arlo Doorbell Won’t Reset
It can be frustrating if your Arlo doorbell won’t reset.
A common theme that customers experience is that the doorbell doesn’t reset properly after a failed firmware update.
It is important, therefore, to make sure that your WiFi network is stable and that the doorbell has power before initiating a firmware update.
Copyright article owner is ReadyToDiy.com for this article. This post was first published on May 26, 2022.
If your Arlo doorbell will not reset or sync, make sure that your Wifi connection is active and that the doorbell has power. The battery should be 100% charged before resetting the doorbell. Turn the power off or remove the battery for 15 seconds then switch it back on.
The Arlo doorbell is sensitive to extremes of temperature. If the outside temperature is outside the range of -4F to 113F (or -20C to 45C) it may not function correctly. Remember that temperatures may be colder or hotter than you think, especially if the doorbell is in direct sunlight or a wet and windy spot.
[This article and its contents are owned by Ready To DIY and was first published on 05/26/2022]
Also, make sure that your router or WiFi hub is close enough to the doorbell that it can have a strong connection. A weak network connection will prevent the doorbell from connecting to your account, which will prevent it from resetting.
Remember that your network connection to the doorbell needs to be properly set up for it to connect to your account. Double-check that your network login credentials are correct.
ReadyToDIY is the owner of this article. This post was published on May 26, 2022.
You must also ensure that the Arlo Secure App is also connected to the WiFi correctly.