DIY

If you have been looking for a way to transform the aesthetic of your space, covering a surface with brick can be an easy and …

After cleaning and preparing the brickwork, apply a ½ inch layer of stucco to the brickwork using a trowel. After covering the bricks, wait a few hours and after the first layer has begun to set, use a plasterer’s rake to lightly scrape the surface. You do this to create a scratch coat.

To install the vinyl siding, start by attaching the foundational strips that hold the vinyl panels in place. They are made up of the starting strip, the J-channel, and the utility trim. After installing the strips, place each panel in place, keeping the joins away from the doors and windows.

After applying a vapor layer and metal lath, lay out the stone veneer and mix up a batch of mortar. Apply the mortar to the stone veneer and apply the stone veneer to the wall. Once the veneer is in place, apply grouting to the gaps and cracks and leave it to dry.

You can install vinyl siding over block. But, pilot holes for each of the nails need to be drilled first because it’s not possible to hammer nails into block. Construction contractors recommend installing wooden framing onto a block wall first and nailing vinyl siding into it to save time.

You can install vinyl siding directly over clapboard without any problem. As long as you prepare the clapboard in advance by cleaning it and getting rid of any potential problems that could lead to issues under the vinyl siding, you can install the vinyl siding directly over it.

To put stone veneer over drywall, begin by installing the cement board or backerboard. This is the only way you can safely put stone veneer over drywall. Otherwise, the drywall won’t be able to bear the weight of the stone veneer, which may cause damage to the structure.

After attaching a lath or cement board to a drywall, measure your stone tiles and make sure that the pattern lines up. Then use a level to draw a horizontal line across the wall and lay the first line of tiles on the line. Work up to the ceiling from the line. Lay the bottom tiles from the floor up.

When putting bricks over siding, you must first remove the siding and replace it with brick. Once you have the angle iron in place, you can start to lay the bricks. Start by placing a layer of mortar and press each brick into it. Check their positioning with a spirit level.

Hybrid flooring is becoming a more and more popular choice, especially when it comes to its moisture-resistant properties. Is it possible to put hybrid flooring …

When it comes to flooring options, you might be surprised by all of the different options you have available. One of those is LifeProof flooring. …

Anytime you are working with a fireplace, you need to be cautious because changes can be hazardous. If one of those changes is putting stone …

If you have stucco on your exterior walls, you may want to put some stone over it. This will help to dress it up but …

Are you ready to give your brick home a new look? One of the options you may be considering is a stone veneer. Can you …

You can put stone over stucco as long as the stucco is prepared in advance. This would include cleaning and putting on a scratch coat. You also need to install a weep screed and flashing to keep water from going behind the stone and to allow it to run off.

There is nothing quite like having a nice fireplace in the home. It’s a centerpiece of the room and it helps to keep us warm …

It is possible to put plaster over ceiling tiles but you need to be careful. Ceiling tiles do not typically have the strength necessary to hold up plaster and they may not be porous enough to adhere to plaster. If you prepare properly, the job can go smoothly.

Generally speaking, there is no problem with plastering over cables or electrical wires. The coating on the wire will protect it sufficiently from the drywall mud. There are also options to help protect the cable or wire even further, and these may be considered as well.

Both a natural stone and an artificial stone veneer can be put over exterior brick. Before you do so, you will have to prepare the brick by either adding a scratch coat or otherwise preparing the brick underneath. It’s a great way to update the home and add some beauty.

Epoxy can be used for a wide variety of purposes. It’s a convenient way to add a finish to everything from a kitchen countertop to …

When working with acrylic paint, you may sometimes want to beautify it or protect it. You might even want to change the color and one …

When you are doing some type of painting, you may want to use epoxy paint. Depending upon what is underneath, it may be hard to …

You can use a wet saw to cut through cultured marble easily. It is the tool that was essentially designed for this type of job. Since it uses water as it is cutting, it helps to keep both the cultured marble and the saw blade cool so that they last longer and it doesn’t burn as it is cutting.

You can use a heavy-duty Dremel tool to cut through timber but it is not something that can typically be done by a crafting Dremel tool. It is also important to choose the proper cutting bit so it will go through the timber without ruining the blade in the process.

You can use a jigsaw to cut ceiling tiles as they have the ability to make straight and shaped cuts on a range of different materials. Depending on the type of ceiling tiles you intend to use, you need a jigsaw equipped with a special abrasive carbide edge blade or diamond-tipped.

Do you need a steel bar for a DIY project you are working on and wonder what cutting tool will be perfect for reducing it …

You can put a backsplash on uneven walls, but they are best suited for surfaces that are smooth and even. To install a backsplash on an uneven surface, it is necessary to attempt to even out the wall to your best ability, to avoid difficulties during the process.

We do not recommend installing countertops on uneven walls as they will cause large bumps and dents in your counters, sink, and tub. An alternative to countertops are stainless steel strips or laminate kitchen carpentry, which are easier to install and come in various sizes.

You can put patio stones on uneven ground, but many experts agree that a level ground is much more suited for the job. However, it could be challenging to have a completely level site before installing a patio due to the surrounding conditions, such as boulders, tree stumps, etc.

To put vinyl siding over asphalt, identify the starting point and install the starter strips. Set up the corner posts, put the J channel along the doors and windows, and apply the flashing to prevent moisture. Install the siding panels to complete the process.

Plaster is porous and easily allows moisture in. Look for the primary source of dampness in your property. It could be faulty plumbing, leaking gutters, downpipes, small gutters, or poor insulation. Stop the sources, and apply your new plaster well. The new plaster coat should not leave any cracks.

You can put plaster over cracks on ceilings or walls, provided you have the right tools. For the best results, consult an expert. Inspect the crack, gather the wanted tools and gently apply the plaster to the crack. Clean up and remember to monitor the area for any other structural damage.

Overall, plaster can be applied over caulk. But, ideally caulk should be used after a wall or surface has been plastered. To allow better adhesion rough up the caulk using a coarse grit sandpaper. After that plaster can be applied using the regular method of plastering a surface.

You can put a stone veneer on a concrete/cement surface, provided you have the required tools. Working with a professional for the best results is advisable, especially if the project is huge. Measure the concrete surface well, use the right veneer stones and install veneer stones carefully to avoid future cracks. 

Generally speaking, there isn’t a problem with applying plywood directly over OBS. It can be attached in place with nails or screws. There are a few potential problems since you are dealing with two different types of wood but for the most part, this double layer of wood will not be a problem.