There are three methods of installation you can choose from when it comes to putting hardwood on basement flooring. You can use nails or screws, glue, or clips. Each method has its own appeal and it depends on your preference for which one you choose.
To get started, you’ll need to remove any existing paint or stain from the concrete surface and sand the surface of the concrete until it is smooth and clean. Use a power sander with medium-grit sandpaper to remove loose concrete or cinder block pieces.
Remove existing carpet and clean and dry your area well. Install risers and stringers to the front and sides of the stairs using wood nails. Measure out your wood and cut it to size. Finally, install the planks to the surface of your stairs using nails, then sand and finish the wood to your liking.
Install roofing felt and 17 gauge metal netting to your metal wall using nails. Mix your stucco. Then, use a trowel to apply the stucco. Use long and even strokes to get your desired texture. Take your time to get the result that you want and wait for the stucco to dry correctly.
Installing stucco to the exterior of your home is a simple process. First, mix your stucco according to the instructions on the package. Next, you can either use a shovel to throw the stucco to the wall or a trowel to apply the stucco. Use a trowel to smooth the stucco out to your desired texture.
To apply stucco over wood siding, prepare the surface by cleaning it and then install a moisture barrier and metal lath. Apply the stucco in at least two coats, making sure that the top layer adheres properly to the scratch layer. Use the proper tools for a smooth finish coat.
Your Miele dishwasher bottom spray arm not spinning may be due to the reasons listed above, and additionally, it may be affected by a blocked pump and filter. If the water pump and filter are clogged, they won’t be able to generate sufficient pressure for the bottom arm to spin.
As a general rule, if you find that the Frigidaire dishwasher fills but does not wash (how to fix), it may be blamed on one of the following five reasons: a blocked inlet valve, blocked spray arm, damaged wash arm support, clogged impeller, or faulty circulation pump motor.
Putting up veneer doesn’t have to be an impossible DIY task. You just need to be able to pull off the baseboard, move your furnishings, gather materials, and prepare the wall. One of the most important things is lining up your board and veneer pieces, and making the necessary measurements.
Start your bamboo flooring installation on the stairs by putting up the risers. Make your way from the bottom of the stairs upwards. Then, you can proceed to doing the bamboo flooring planks nosing, or the ready-made treads. Add molding under the overhang of the plank for a finishing touch.
To install stone veneer over cement board or Durock, start by mixing a batch of mortar according to the manufacturer’s instructions. Use a trowel to spread a thin layer of mortar onto the surface, creating a rough, textured surface for the stone veneer to adhere to.
To install carpet tiles on stairs, measure and cut the tiles to size, clean and sand the stairs, apply adhesive, and press the tiles into place. Use a knee kicker or stair tool to stretch and secure the tiles, and trim away the excess with a utility knife. Hammer in nails at the edges to secure the tiles.
Reciprocating saws, including a Sawzall, can cut through galvanized wire easily. You should have the right type of blade on the reciprocating saw so it cuts through the wire rather than pulling it. In addition, you need to consider the power of the tool, which may be too much for some jobs.
An oscillating tool is an excellent option to have available when cutting shingles. It does not necessarily replace the need for a utility knife or roofing knife, but it can work when you need something in a situation where you have to cut it quickly and cleanly.
Applying stone veneer to the surface of your concrete steps or walkway can be a great way to transform the look of your home. If …
In general, you can put vinyl siding over metal. But, you first need to install a wood frame called furring over the metal. Vinyl siding needs to be nailed to the wall, which is not possible for metal. Installing a wood frame is also done when vinyl siding is installed over concrete and block.
As a general rule, vinyl siding can be installed over cement board such as Durock. Wooden framing called furring should be installed if the cement board is thinner than ⅝ in (1.6 cm). The reason is the nails or screws used to attach the vinyl siding need to penetrate at least ¾ inch (1.9 cm).
In general, you install vinyl siding into concrete. However, construction contractors recommend first installing a wooden frame made of furring strips. Otherwise, it’s a lot more work to drill pilot holes where the vinyl planks need to be attached to the concrete using screws.
Overall, first install wooden framing to have a place to nail the vinyl siding to. Then install the F channels along the sides, and the starting strip. After that install each row of vinyl planks one by one by cutting them to fit, sliding them into place, and nailing them in.
In general, stone veneer can be installed over OSB, and is a recommended material to be used under stone veneer. The process to install stone veneer over OSB is the same as installing stone veneer on other types of materials suitable for stone veneer. Below is how to do it.
Generally, if all lights are flashing, restart your Hotpoint washer by unplugging it at the wall and plugging it back in again. If all the lights still flash clean the water filter (front loading washers only). When they continue to flash, or you have a single light flashing refer to the steps below.
The fuse between the fan and the power supply has failed and needs to be repaired to be replaced, the convection setting has been accidentally changed which turns the fan off, there is a glitch with the internal computer, and your air fryer needs to be restarted.
The best place on earth is your home. It is a place where you can relax and just be yourself. Your home décor is where …
You won’t need many tools to install hardwood click-locking planks over asbestos tiles. It will be necessary to measure the room so you know you have enough planks, though. Also, you’ll need cleaning supplies to clean the tiles before installing the planks.
Whirlpool dishwashers are quite popular all over the globe, and people love these appliances because they look good and typically work really well. However, nothing …
Examples of the tools you need to put stone over concrete patio/steps include spacers, paver edging, grinder, circular saw, diamond tip saw blades, level, landscaping cloth and a broom. You’ll also need stones, leveling paver sand, polymeric sand, water, etc,to accomplish your project.
Collect the tools you will require and ensure they are all clean. Inspect the current asphalt/blacktop surface and confirm it’s clean. Measure your workspace to know how many stones you need, gauge the slope, and prepare the site for the actual stone paving installation.
To lay bricks sideways, create a strong foundation below the ground level. The deepness of the foundation depends on the size of your project. Mix mortar and start laying your bricks sideways. Apply your mortar in between the bricks and a sealant. Clean the site when done.
You should first have asbestos removed and disposed of safely. Then install a moisture barrier followed by soffit and fascia siding. Next, you can measure the walls and install the starter strip. You should install corner posts and flashing and j-channel around doors and windows. Lastly, install the panels using nails that are 16 inches apart.
First, you should remove all rotted or damaged wood. Next, you can install a moisture barrier and soffit fascia siding. You can then install corner posts and j-channel around the doors and windows. Next, measure your walls and cut the vinyl to size. Install the starter strip and begin to nail the panels to the wall spacing them 16 inches apart.
Stucco walls always look so pretty and really make a home stand out, but many people think it’s not something they can do themselves. Although …
The Kindle has changed how we read and it has never been so convenient before. These devices are awesome for reading your favorite books while …
To put brick over drywall, wear your protective gear, measure the room and sketch the correct dimensions on your drywall. Protect your flooring with a tarp, clean the bricks and apply adhesive. Gently place the brick on your drywall, and use a sealant. Clean the site when done.
If your concrete is painted or treated, you will need to install a metal lath over the concrete to create a surface to which the stone veneer can adhere. Next, apply scratch mortar and let it dry for two days. You can then use mortar to coat the back of each stone and place them where you want on the scratch coat. Repeat this final step.
If you have been looking for a way to transform the aesthetic of your space, covering a surface with brick can be an easy and …