Skip to Content

Shark Robot Vacuum Not Working

If you are someone who always has a mess on your floors but never has the time to clean it, you might have found yourself with the incredibly powerful and convenient Shark robot vacuum. If your vacuum suddenly stops working though, what can be done to restore the device?

If your Shark vacuum isn’t working, be sure it is connecting properly to its charging station, ensure no wires are damaged that connect the charging dock to power, reset the router, gently push the vacuum onto the charging station to engage it with the dock.

Black vacuum cleaning the floor

Shark vacuums offer owners the ability to keep the floors of their space spotlessly clean through their automatic vacuuming abilities, tailored to go through their individual home or business. This allows owners to stop worrying about the messes that happen on their floors, as this device will have it cleaned up within a matter of seconds. Although the Shark robot vacuum lives up to its reputation, take a look below if your device suddenly stops working.

Shark Robot Vacuum Not Working

A Shark robot vacuum is designed to replace the clunky vacuum that you have stuffed away in the closet, while also replacing the need for you to be present when vacuuming takes place. The Shark robot vacuum is able to work to navigate the exact space it is intended to be used within all without you ever having to lift a finger. If you own a Shark vacuum and it is not working as it should, take a look below to see what can be done to get the device back on track.

If your Shark vacuum isn’t working, be sure it is connecting properly to its charging station, ensure no wires are damaged that connect the charging dock to power, reset the router, gently push the vacuum onto the charging station to engage it with the dock.

If your Shark Vacuum still isn’t working, check any dysfunctional side brushes for obstructions by removing the brushes, clear any debris that is caught within the brush roll, remove the front wheel and clean anything obstructing its rotation, and confirm that the vacuum has been programmed with the correct date and time for any scheduled runs.

Shark Robot Vacuum Not Turning On

Black vacuum cleaning the floor

There are a variety of different operations and functions that Shark vacuums are capable of, but one of the most basic abilities is to simply turn off and back on. Just like any other device, a Shark vacuum must turn on in order to perform what it has been designed to do, which is vacuum a space. If you have set your vacuum to operate at a certain time or manually implore it, but it will not turn on, take a look below to see how to resolve such an issue.

If your Shark robot is not turning on, one common issue could be a drained or faulty battery. First, ensure the vacuum is properly placed on its charging dock and that the dock is connected to a power source. If the battery is old or has been used extensively, it might need replacement. A new battery can often restore functionality to the vacuum.

Another potential cause for a Shark robot not turning on is a blockage or debris caught in the brushes or wheels. Turn the robot over and inspect for any tangled hair, threads, or other debris that might be obstructing the movement of the brushes or wheels. Remove any obstructions you find, as these can prevent the robot from starting its cleaning cycle.

Lastly, the issue might be related to the robot’s sensors or software. If sensors are dirty, they may not function correctly, hindering the robot’s ability to start. Clean the sensors gently with a soft cloth. Additionally, if the robot’s software is outdated, it might cause operational issues. Check for any available updates through the SharkClean app and install them to ensure the robot is running the latest software. This can resolve technical glitches and improve the robot’s performance.

Shark Robot Vacuum Not Connecting to WiFi

Black vacuum cleaning the floor

Not all Shark robot models are capable of or need a WiFi connection, but for those that are able to connect to WiFi, users can operate and command their vacuum through an application on this phone through this connection. However, if the Shark robot vacuum will not connect to WiFi, you will not be able to operate it from a separate device at any capacity. If your Shark robot vacuum is not connecting to WiFi, read on to see what can be done to establish this connection.

If your Shark robot vacuum is not connecting to WiFi, try resetting your router. To do this, unplug the router from its power source and wait for 60 seconds. After this time has passed, plug the router back in, allow it to reboot, then try once again to connect your vacuum to the WiFi network.

Shark Robot Vacuum Not Charging

Black vacuum cleaning the floor

Outside of Shark Vacuums not needing a person to guide them in completing clean up tasks, one of their biggest appeals is that they also don’t need to be connected to a cord to do so. By using a charging dock, all Shark vacuums complete their work and find their way back to the dock to charge back up for the next session. If you notice that your Shark vacuum has been at the dock for a while but has still not charged, read below to see what can be done.

If your Shark robot vacuum isn’t charging, it could be that the vacuum is not making proper contact with the charging dock. Gently push the vacuum towards the doc to help it engage. If this movement causes the vacuum to charge, you will see flashing blue lights on the top of the vacuum.

Shark Robot Vacuum Side Brush Not Spinning

Black vacuum cleaning the floor

Another great feature of Shark robot vacuums is that they are designed to reach just about any nook or cranny within your home or business and this is all made possible by the side bruises that extend on either side of the device. You don’t have to worry about odd angels with this device because of those bruises, but if you see that they are not spinning, the robot will not be able to sweep those pieces underneath and up into its holding chamber.

If the side brushes on your Shark robot vacuum are not spinning, it could be that something has wrapped around the post which helps to rotate the brushes. To clean this area, simply remove the brushes from their post by pulling upward at the base of the bristles.

Shark Vacuum Keeps Stopping

Black vacuum cleaning the floor

When it comes to the behavior of Shark vacuums, there are going to be times when the device stops or pauses to make a turn, encounters something that is obstructing its path on the floor, or has been given a different command by you on your smart device. However, if you notice that your Shark vacuum is stopping over and over again without any explanation, read on to see what might be causing this and what you can do to prevent it from happening any longer.

If your Shark vacuum keeps stopping, there is likely something within the main brush roll that has gotten stuck. To clean the brush roll, remove it by pressing both tabs and remove the brush roll from its port. Once clean of any debris caught within it, it can be reinserted.

Copyright protected content owner: ReadyToDIY.com and was initially posted on February 26, 2022.

Shark Vacuum Keeps Getting Stuck

Black vacuum cleaning the floor

Another great aspect of Shark vacuums is that they are really quite capable when it comes to having to clean around items that may find their way to your floor. By being able to redirect itself after bumping into a large item at times, this affords owners the ability to have a bit of a mess while the mess is still being cleaned. However, if your vacuum continues to get stuck and nothing is in its way but it is also not able to redirect, what can be done to fix the problem?

If your Shark vacuum keeps getting stuck, remove the front wheel from the device to see if there is anything preventing the wheel from rotating. Once you have cleaned the wheel cavity, reinsert the wheel back into its proper position, turn the vacuum back on, and see if it will run smoothly.

Shark Robot Vacuum Not Picking Up Dirt

Black vacuum cleaning the floor

You know that Shark Vacuums can pick up this morning’s spilled cereal, last night’s dog grooming session, and the glitter from last week’s art group, but above all, shouldn’t a Shark robot vacuum be able to pick up dirt without a problem? If your Shark robot vacuum is not picking up dirt and you notice that trails are beginning to be left behind, read on to see what might be the cause of this puzzling issue.

If your Shark robot vacuum is not picking up dirt, it could be that the air filters need to be changed or washed. If they are too full, dirt will be difficult to pick up, therefore thoroughly clean washable filters and allow them to completely dry or replace old disposable filters with new ones.

Shark Robot Vacuum Squeaks

Black vacuum cleaning the floor

When a Shark robot vacuum is in use, you will be able to hear a low humming sound that comes from its motor, but it will be nothing like the sound that emits from the vacuum you got decades ago that weighs as much as a small child. The beauty of this device is its ability to do the work without being seen or heard in an obvious way, but if you notice that your Shark robot vacuum is squeaking, what can be done to stop this irritating noise?

Copyright article owner is ReadyToDiy.com for this article. This post was first published on February 26, 2022.

If your Shark robot vacuum squeaks, the sound is most likely caused by either friction against various parts or something caught within one of the wheels or brushes. Remove the front wheel as well as the side and main brush roll and clear them of any debris before reinserting.

Shark Robot Vacuum Mapping Not Working

Black vacuum cleaning the floor

Mapping is the process Shark robots go through when they are in a new setting, which allows them to explore the area and save all of the various dimensions that it will encounter on a day-to-day basis. This will then be the map that it follows to guide it on future runs so that every corner of your home is kept swept and clean. If you go to set up mapping for your Shark robot vacuum and notice that it is not working, what can be done?

If mapping is not working for your Shark robot vacuum, try resetting the process from your smart device. To do this, go to ‘Settings’ and click on ‘Factory Reset.’ Once you have hit this option, confirm the action and allow the reset to complete, then try mapping the device again.

Shark Robot Vacuum Not Running On Schedule

Black vacuum cleaning the floor

Shark robots not only can map the area in which they have been programmed to clean on a regular basis, but they can also be put on a schedule, which allows owners to set their device to run at a specific time during the day or night depending on what is most convenient for their daily activity. If you have a schedule set for your Shark robot vacuum and it is not running on that schedule, take a look below to see how that can be fixed.

If your Shark vacuum is not running on schedule, check that the robot has the correct time and date programmed to it through the app. If this is the problem, simply reset the time and date, confirm the change, and your vacuum should run on the schedule in place.

If your Shark Vacuum isn’t working, check any dysfunctional side brushes for obstructions by removing the brushes, clear any debris that is caught within the brush roll, remove the front wheel and clean anything obstructing its rotation.

Related Articles

Shark Vacuum Keeps/Not Docking

Shark Robot Vacuum Light Flashing

Shark Vacuum Won’t Connect to WiFi/Phone

Can You Clean Shark Vacuum Filters and Canisters?

ReadyToDIY is the owner of this article. This post was published on February 26, 2022.

How to Reset Shark Vacuum