You will need a tape measure. A saw, a framing angle, painters tape, a pull bar, a pry bar, a finishing nailer, a rubber mallet, spacers, a moisture meter for RH testing, setting materials, barriers, quarter round or baseboards, transition moldings, scrapers or grinders, self leveler, patching compounds and cleaning materials.
After cleaning and preparing the brickwork, apply a ½ inch layer of stucco to the brickwork using a trowel. After covering the bricks, wait a few hours and after the first layer has begun to set, use a plasterer’s rake to lightly scrape the surface. You do this to create a scratch coat.
To install the vinyl siding, start by attaching the foundational strips that hold the vinyl panels in place. They are made up of the starting strip, the J-channel, and the utility trim. After installing the strips, place each panel in place, keeping the joins away from the doors and windows.
After applying a vapor layer and metal lath, lay out the stone veneer and mix up a batch of mortar. Apply the mortar to the stone veneer and apply the stone veneer to the wall. Once the veneer is in place, apply grouting to the gaps and cracks and leave it to dry.
General tips on how to fix/avoid a Hotpoint washer not draining include ensuring that you select the correct setting for each load, washing small items inside a pillowcase or laundry bag to prevent them from straying out of the washer drum, and cleaning the coin trap regularly.
The most common reasons your Miele dishwasher does not heat up are usually faulty heating elements or your thermostat could have stopped working. Another reason could be that your Miele is plumbed into the hot water supply, and the water filling the dishwasher is too hot.
When the KitchenAid fridge freezer door won’t close or seal, it is typically because the fridge is tilted a bit forward. Try adjusting the front of the KitchenAid fridge so that it is just a little higher than the back of the fridge. This should allow the doors to close easily.
You can install vinyl siding over block. But, pilot holes for each of the nails need to be drilled first because it’s not possible to hammer nails into block. Construction contractors recommend installing wooden framing onto a block wall first and nailing vinyl siding into it to save time.
You can install vinyl siding directly over clapboard without any problem. As long as you prepare the clapboard in advance by cleaning it and getting rid of any potential problems that could lead to issues under the vinyl siding, you can install the vinyl siding directly over it.
Overall, ensure the ‘cooling’ function is on using the control panel on your Jenn Air fridge. It gets disabled after a power outage or power surge. Next, inspect the air vents on the interior of your fridge and freezer to ensure they are covered by a food or drink item, then do the steps below.
Overall, your air fryer could be faulty, or the circuit breaker is intended for an appliance that draws less power than an air fryer needs. You need to isolate if the air fryer is faulty, or the breaker is too weak to power all the appliances in your kitchen and your air fryer using the steps below.
In general, a low hum is part of normal operation, and is produced by the drain pump, extractor fan, or water circulation pump. If it seems overly loud, or there is a grinding, buzzing, whistling, or squealing noise contact Maytag support to organize a repair technician.
To put stone veneer over drywall, begin by installing the cement board or backerboard. This is the only way you can safely put stone veneer over drywall. Otherwise, the drywall won’t be able to bear the weight of the stone veneer, which may cause damage to the structure.
After attaching a lath or cement board to a drywall, measure your stone tiles and make sure that the pattern lines up. Then use a level to draw a horizontal line across the wall and lay the first line of tiles on the line. Work up to the ceiling from the line. Lay the bottom tiles from the floor up.
When putting bricks over siding, you must first remove the siding and replace it with brick. Once you have the angle iron in place, you can start to lay the bricks. Start by placing a layer of mortar and press each brick into it. Check their positioning with a spirit level.
Hybrid flooring is becoming a more and more popular choice, especially when it comes to its moisture-resistant properties. Is it possible to put hybrid flooring …
When it comes to flooring options, you might be surprised by all of the different options you have available. One of those is LifeProof flooring. …
Anytime you are working with a fireplace, you need to be cautious because changes can be hazardous. If one of those changes is putting stone …
If you have stucco on your exterior walls, you may want to put some stone over it. This will help to dress it up but …
Are you ready to give your brick home a new look? One of the options you may be considering is a stone veneer. Can you …
You can put stone over stucco as long as the stucco is prepared in advance. This would include cleaning and putting on a scratch coat. You also need to install a weep screed and flashing to keep water from going behind the stone and to allow it to run off.
There is nothing quite like having a nice fireplace in the home. It’s a centerpiece of the room and it helps to keep us warm …
It is possible to put plaster over ceiling tiles but you need to be careful. Ceiling tiles do not typically have the strength necessary to hold up plaster and they may not be porous enough to adhere to plaster. If you prepare properly, the job can go smoothly.
Generally speaking, there is no problem with plastering over cables or electrical wires. The coating on the wire will protect it sufficiently from the drywall mud. There are also options to help protect the cable or wire even further, and these may be considered as well.
Both a natural stone and an artificial stone veneer can be put over exterior brick. Before you do so, you will have to prepare the brick by either adding a scratch coat or otherwise preparing the brick underneath. It’s a great way to update the home and add some beauty.
Epoxy can be used for a wide variety of purposes. It’s a convenient way to add a finish to everything from a kitchen countertop to …
When working with acrylic paint, you may sometimes want to beautify it or protect it. You might even want to change the color and one …
When you are doing some type of painting, you may want to use epoxy paint. Depending upon what is underneath, it may be hard to …
You can use a wet saw to cut through cultured marble easily. It is the tool that was essentially designed for this type of job. Since it uses water as it is cutting, it helps to keep both the cultured marble and the saw blade cool so that they last longer and it doesn’t burn as it is cutting.
You can use a heavy-duty Dremel tool to cut through timber but it is not something that can typically be done by a crafting Dremel tool. It is also important to choose the proper cutting bit so it will go through the timber without ruining the blade in the process.
If you have a ceramic tile floor in your home and you want to change the look, you might consider using some peel-and-stick tile. Does …
When it comes to DIY projects around the home, you will have a difficult time finding one that is easier than peel-and-stick tiles. What if …
In situations where the carpet is already installed and you do not want to risk ruining it, installing sheet vinyl flooring over thicker carpet isn’t professionally advisable. To get the best results, we’ve found that it is always best to install sheet vinyl flooring on a solid floor, as this way it tends to last longer.
You can use a jigsaw to cut ceiling tiles as they have the ability to make straight and shaped cuts on a range of different materials. Depending on the type of ceiling tiles you intend to use, you need a jigsaw equipped with a special abrasive carbide edge blade or diamond-tipped.
Do you need a steel bar for a DIY project you are working on and wonder what cutting tool will be perfect for reducing it …