Sometimes glitches and malfunctions can cause the control panel on your Maytag refrigerator to not work properly. Thankfully, resetting the power to the product can help fix the problem. This will, however, require unplugging the appliance from its power source.
The most common cause of a Sonos Move speaker not switching to Bluetooth is outdated firmware. Thankfully, this problem can be fixed by connecting the speaker to Wi-Fi and updating its firmware. To do this, open the Settings tab and click System > System Updated > Check for Updated.
To reset the KitchenAid refrigerator alarm, unplug the device from power and let it sit for ten minutes then plug it back. Alternatively, press the alarm reset button for 10 minutes and then release it. The above two options should help you reset the KitchenAid refrigerator alarm.
Your KitchenAid refrigerator water dispenser could be slow or dripping due to a clogged or incorrectly installed water filter. To see if that’s the problem, remove the filter, then dispense water to see if the water flow goes up. Another possibility is that there is air in the water system.
To reset/fix Sonos Roam/Roam SL, press the power button until the LED lights go out with a sound. While pressing the play/pause button, press and release the power button. Continue pressing the play/pause button until the speakers flash an orange and white light.
A GE smart switch solid red light might imply that the switch is overloaded or that the switch needs to get more power. In addition, the solid red light may also indicate that the switch has a poor connection to the internet or a faulty power connection.
A GE smart switch with no power can be due to power outages, a tripped circuit breaker, a faulty smart switch, or an air gap switch that is not fully pressed in. Check your home’s power supply and reset the circuit breaker. Ensure the air gap switch is fully pressed, and replace the smart switch.
It happens sometimes. You charge your Kindle, looking forward to another round of uninterrupted reading, but suddenly, you can’t turn it back on. Is it …
To apply plywood to sheetrock or drywall, you first need to use a stud finder to find the studs in your walls to ensure the plywood is anchored properly. Then you should use your wood screws and drill to secure your plywood where you need it to be. Fix your outlets and trim with molding.
To install plywood over a brick wall you need to clear your area of all furniture to give yourself space to work. Next measure and cut your plywood to size. When your plywood is the right size you can begin installing it with a power drill and concrete screws. This will ensure that the plywood stays secured to the brick.
The first thing you should do is clear your area of all furniture to give yourself the room you need to work. Next, get a putty knife and hammer to remove the asbestos tiles carefully. Then you can measure and cut your plywood. Install the plywood using a power drill and the proper screws to secure it.
Installing plywood on top of a carpet is not really something that comes highly recommended, but if you really need to, there is a way …
There are three ways to install wood over tiles, but some preparations are required and the methods aren’t completely guaranteed. You should lay a subfloor to prevent damage to the tiles if you want to nail the plywood in place. Otherwise, you can glue the plywood, which also requires preparation.
Any time you are having a problem with your Bosch refrigerator icemaker, you should check the temperature in the freezer. If the temperature is not low enough, ice will not be made. Otherwise, you can try resetting the system by unplugging the refrigerator and plugging it back in after five minutes.
Anytime you are having a problem with your Bosch refrigerator freezer not freezing, you should check the condenser coils. If you can access them, make sure they are not frosted over and do not need cleaning. Otherwise, reset the refrigerator by unplugging it for five minutes.
There are certain appliances in our home that we just assume are going to be working at all times. This includes our refrigerator. What can …
Epoxy works well when it is put on metal either for covering it or for adhering metal to another product, such as plastic or another type of metal. There are some things that need to be prepared in advance so that you can work with them properly, but it will work well.
There are many times when we may want to work with aluminum. It is a common metal and we might even want to add some …
Epoxy is used to finish off many different types of materials. Is it also something that can be put on plywood? You can put epoxy …
When measuring your floor, make sure that the long edge of the plywood is placed across the direction of the joists to ensure maximum strength. If the floor is not completely stable, you can insert additional support between the joists and screw the plywood into them.
It’s ideal to use plastic primer paint. Other supplies you need for a glitter tumbler crafting project include a cup turner (you can DIY this at home or buy a heavy duty one), tiny measurement cups, glitter, popsicle sticks, gloves, silicone brush and mat, heat gun, mod podge, and sandpaper.
To put epoxy on the cutting board, pour the epoxy/ hardener mixture at the centre of the cutting board, then use a painter’s brush to spread it to the edges of the board to form the first layer. Let the initial layer sit on the board for at least 4 hours, then top up the second layer.
You should clean and dry your Corian. This will ensure that no moisture is left behind. You can check by sealing a plastic sheet over your Corian. If any moisture is left, you will need to dry it further. Apply your epoxy and let it dry. Sand the surface of your Corian to help the epoxy adhere better.
You need to clean and dry your area well to avoid getting moisture trapped under your epoxy. Next, sand the surface of your polyurethane or polyacrylic. Get rid of all of the dust before you mix your epoxy and begin to apply. You will need to let one coat dry and apply a second coat after 24 hours.
To perform a hard reset on the Whirlpool Oven, turn the circuit breaker or fuse connected to the oven to the Off position. Wait at least one minute before turning the circuit breaker or fuse back on. Turn the oven on and select the Bake setting. This will reset the appliance.
When the GE Smart Switch won’t turn off, try pulling out the air gap and waiting 10 to 15 seconds before pushing it back in. The air gap is located at the bottom of the switch and looks like a little button. It doesn’t come out of the switch all the way.
If you are going to put plaster over plywood, you will first need to cover the plywood with plasterboard. Once the plasterboard has been installed, countersink the screw heads in the plasterboard and then fill the joints. Use metal angle beads around all external corners to create a crisp finish.
You can reset a Galanz microwave by pressing the start button until the microwave displays ‘00:00”. Press 1,2,3,4,5,6,7,8,9,0, followed by the power level button. Press X2, prog, switch, stop and then start. The microwave will display “00:18,” indicating a successful reset.
First lay plastic over your floor, taping the edges to check for moisture, and cover the walls with plastic to protect them. Once there is no moisture left behind, sand the surface of the paint to de-gloss it. Mop and clean the floor. Mix your epoxy and begin to apply it to the concrete.
As a general rule, the tub can’t drain the water that’s in it due to clog, or the tub is out of balance. It’s common for the tub to go out of balance, and you should adjust heavy items in the tub to spread them out. Otherwise, do the steps below to identify why it’s happening.
In general, your microwave is accidentally set to demo mode, the temperature/power setting is set too low, the control lock is on, the door is not closed properly, there is an error code showing on the display, or one of the internal components has failed.
As a general rule, the wall outlet is not supplying power, the power switch for your fridge is not turned on, or one of the internal components has failed. Test the wall outlet your fridge is plugged into is supplying power by plugging something else into it. Then do the steps below.
There may be a number of different reasons why you would want to color a piece of glass. Regardless of whether it is a windowpane …
Art takes on many different forms but at times, it may mean putting some epoxy on canvas. Regardless of whether you are preserving your artwork …
You can apply epoxy over cracked concrete but it is always better to repair the concrete before doing so. Use a sealer for repairing some of the larger cracks and a coat of epoxy for repairing any hairline cracks. You can then finish it off with the final coat of epoxy.