A dryer that keeps shutting off is often a problem with the door switch. If the switch is loose or failing, the vibration from the dryer will cause it to move and shut the dryer down. In other words, the switch determines that the door is open, even if it is closed. Replace the switch to fix the problem.

Preparing the laminate floor by washing and sanding it will allow the epoxy to adhere to it properly. It is necessary to sand away the finish of the laminate to do so. You should also tape the entire room, including the edges and anything that can’t be moved from the area to ensure it doesn’t get ruined as you are putting down the epoxy.

When it comes to your MacBook not detecting additional monitors or external hardware, first check that you have properly detected all external devices in the System Settings folder. If that does not work, make sure that the cables are in working condition, you have run all required updates, and you have the correct adaptor.

If your dryer continues to run, the typical problem is with the mechanical timer. A timer works by timing the load and stopping the appliance when the cycle is complete. If it is failing, it may not reach that point in the cycle. A timer can be replaced but it is not typically possible to fix it.

If the Do Not Disturb feature isn’t working on your Samsung device, be sure that you have all contact favorites deselected so that no calls will come through, go through the ‘Exceptions’ section to allow for particular apps to be able to notify, and turn your phone off and back on.

If your Chamberlain Garage Door Opener isn’t working, check that power is present at the outlet your wall opener is plugged into, see that the trolly hasn’t gotten hung up on a screw, replace the lightbulb within the light, and test the light socket and logic board to see if they need replacing.

If your LG screen share isn’t working, try resetting your network and be sure to disconnect any devices that are connected to the network but are not being used when screen sharing. You can also connect directly from other devices by clicking the screen sharing icon or notification icon.

If your Roper washer isn’t spinning or working as it should, check to make sure that the drive belt does not have any obvious damage and if it does, replace the piece, and be sure you don’t interrupt the auto fill process by adding extra clothing during the fill phase.

If your Roper dryer is not heating or working as it should, be sure that the gas supply valve has been turned to ‘On’ if your appliance is run by gas, check that the dryer is plugged in securely if connected, replace the heating element if faulty, and check for continuity within the timer motor.

If your GE dishwasher isn’t starting, ensure that the ‘Delay Start’ button has not been turned on, check that the door is latching if you are experiencing issues with the door sensor, use a multimeter to see if the start switch is working, and disable the lock mode function if enabled.

To reset a smart TV, turn off the TV and either disconnect the device directly from its power source or unplug the power cable from the device itself. You will then hold down the power button on the TV for 3-5 seconds, release the button once the time has passed, the power on the device.

If your Estate dryer is not spinning, the dryer belt could be loose or broken. The belt is what rotates the drum. If the belt is defective, the dryer will turn on but the drum will not spin. If you can easily rotate the drum by hand, the belt needs to be replaced.

If your Hotpoint washer is not filling, check the fill hose and screen. If the hose is kinked or pinched, water will not reach the washing machine. A clogged fill screen can also impede water flow. Remove and dirt, debris, or hard water build-up from the screen.

If your Admiral dryer keeps beeping, this is a safety feature that could be notifying you the load is too heavy. An overloaded drum will prevent warm air from circulating through the laundry. The vents could also become blocked preventing heat from escaping outside.

If you need to reset your Sharp TV and reset because of a black screen with no picture, turn off your TV using the Power button on the TV Remote. Then, wait for one half minute to one minute and turn the TV on again and check to see if any picture is appearing.

If your Samsung Phone won’t connect to your computer, monitor or printer, and won’t connect to your printer, make sure that your Wi-Fi connection is turned on.  Open Settings and then tap on Connections and then on Wi-Fi. Turn on Wi-Fi and then check your phone’s connection to your printer.

Your first step should always be to check the power cords. Make sure that your MacBook has been properly plugged in. If it everything is connected correctly, you should then look at running a hard restart. This can solve issues that may have arisen from an update or software glitch.

If your Xbox remote keeps blinking, as a general rule, you should first replace the batteries in case they are low. Then reconnect your remote. Press the connect button on the front of your Xbox. Then press and hold the connect button on your remote until the Xbox symbol stops flashing.

If your Dell Printer is not working and keeps cancelling jobs, try connecting the Dell printer to the computer via a USB. Then change the port from USB to TCP/IP (wireless) on the Dell Printer Driver and then reconnect back to Wi-Fi and try to complete your printing jobs again.

If your Epson Printer is not working and won’t stay connected to Wi-Fi, begin by restarting your Epson printer. Push the Windows Button + I button and Launch Windows Settings. Go to Devices and then double click on it. Click on Printers and Scanners.  

If your LG won’t go past the LG screen, you might be experiencing a system glitch. Some of the methods to fix the issue involve erasing all of your data. Therefore, you should always try the easy methods first. Next, you can try the factory reset if you don’t get positive results.

The data and cache for the Samsung Pass app can be corrupted, so deleting it can fix this issue. Then do a soft restart of your Samsung device, make sure the Samsung Pass app permissions are enabled, and finally that you have a data or Wi-Fi connection and that it’s working.

If your Blink Camera is not recording sometimes, adjust the delay in the Retrigger Time. This is the time between the cameras detecting motion and recording. If the retrigger time is too long, any motion in the time frame will not be detected and will not be recorded.

You can change Wi-Fi on your Blink Camera by doing a factory reset. This will delete any saved information and preferences. Press and hold the rest button until the red light turns blue. The camera has now been returned to its original factory settings.

If your Blink Camera is not updating, make sure you have enough signal strength to allow for updates. You can also manually update firmware by going to the Blink Camera settings and selecting General > Software Update > Automatic Updates. Follow the onscreen instructions.

If your Canon Printer is not working and won’t stay connected, press the Setup button on the printer. Locate Device Setting and press Ok.  Press on the Arrow Buttons and then when you see LAN Settings press OK. Then scroll to Other Settings and press Ok.

If your Brother Printer is not working and is not finding a network, download the Brother Network Repair Utility from support. Brother.com. Save this in a folder on your hard drive. Click on the Nettool folder and then click on BrotherNetTool.exe and follow the instructions on the screen.

As a general rule, your Samsung GPS not working in airplane mode is usually related to phone software or app software issues. Placing a phone in airplane mode does not affect its ability to receive GPS signals. Updating your software and restarting your phone should resolve the issue.

If your LG phone Wifi isn’t working, make sure that you have Wifi enabled on your device, forget the network you are currently connected to then reconnect back to it, reset the Network settings within your phone, reset the router, and switch off the Auto Connect feature.

If your phone keeps freezing, restarting, or turning off, be sure the device is fully charged, that no third-party apps are present on the phone, free up memory space if too much is stored on the device, and complete a soft reset or remove the battery to stop these issues.

If your LG phone won’t ring or vibrate, make sure that you have the volume turned up to an audible level, that you have the mute button disabled, that ‘Do Not Disturb’ has been turned on, complete a factory reset, or move to another location to improve cellular service.

If your LG phone won’t send or receive messages, be sure to delete any stored messages on your phone, as they take up storage which may be the cause of messages not being received, turn the phone off and back on to reset it, and connect to a stable and reliable network.

If your Samsung freezer is blinking/blinking temperature, the temperature inside the freezer is too warm. The blinking display means the freezer has reached 56 degrees Fahrenheit. Adjust the temperature to a cooler setting and the blinking will stop.

If your Samsung refrigerator compressor keeps running, make sure the refrigerator is not too full. If the refrigerator is too full, the compressor has to work harder to keep warm air out and the inside temperature cool. There also needs to be enough room between items for air to circulate.

If the Samsung fridge fan is not getting power, the thermistor could be faulty. The thermistor monitors the temperature inside the fridge, sending readings to the control board. If the thermistor is defective, the compressor and evaporator fans will not be signaled to turn on and cool the fridge.