If the Samsung fridge fan is not getting power, the thermistor could be faulty. The thermistor monitors the temperature inside the fridge, sending readings to the control board. If the thermistor is defective, the compressor and evaporator fans will not be signaled to turn on and cool the fridge.
If your dryer is not drying, it is likely due to a setting. If you are using auto dry, try using a timed dry setting instead. Auto dry is always preferable but if the sensors are going bad or if you are overloading the dryer, you may need to time the dry cycle instead.
If your LG Subwoofer is not working and is not pairing, go ahead again and check on the back of the subwoofer for the Pairing Button. Press and hold it for at least five seconds. Then you will see the subwoofer’s LED light blinking green and red in succession.
If the drum rollers are going bad, you will have a difficult time spinning the drum by hand. The proper way to test this is to take off the belt and attempt to spin the drum. If the drum is locked up or feeling as if it doesn’t want to rotate properly, then you can visually inspect the rollers to see if they have anywhere.
The answer is yes. Read receipts are easy to enable or disable at anytime. You simply enter your message setting menu and find the section marked ‘More Settings’. Once you are on that menu, you can turn on and off both your text messages as well as multimedia message read receipts. It is as simple as toggling the button next to ‘Text Messaging’ and ‘Multimedia Messaging’ to the right where it will turn blue to show it is enabled, or to the left where it will show as gray to let you know that it is disabled.
If your dryer is not turning on it is a problem with the door switch. The door switch lets the control board know if the door is open so it will not operate. It is a safety feature built into the dryer. When the door switch is faulty, it may indicate that the door is open, even when it is closed.
Here are steps to take if your Samsung subwoofer keeps cutting out. First, check to make sure that all of the connections to the soundbar and the subwoofers are correct and functioning. You also want to be sure that you are trying to get sound from something compatible with both. There could also be an issue with the subwoofer. You can verify this by running a soundcheck.
When a dryer is not starting, it may need to be reset. You can unplug the dryer from the power or turn off the circuit breaker for a few minutes to allow the power to dissipate. After reestablishing the power, wait a few minutes and then try operating the dryer as normal.
If Samsung Pay isn’t working, be sure you are in a location that supports this feature, confirm that your device is connected to a reliable network, uninstall and reinstall the app, turn the device off and back on, disable the pop-up feature, or reset the app.
Since most refrigerators don’t have an automatic reset function, it is necessary to disconnect the refrigerator from the power source and reconnect it again. This is done by unplugging the refrigerator or turning the circuit breaker to the off position. Wait at least five minutes before reestablishing power again. This will fully reset the refrigerator.
The most common reason to reset a dryer is if the cycle was interrupted. Like many home appliances, a dryer has a memory and it may want to pick up where it left off when it was interrupted. Resetting the dryer will start it at the beginning of the cycle again.
Generally speaking, you can reset a washing machine by disconnecting the power. The easiest way is to unplug it from the wall but you can also flip the circuit breaker and fully disconnect it from the power in that way. After allowing a few minutes to pass, reconnect the machine and give it 30 seconds to fully restart before using it.
It is possible to remove epoxy from concrete but you need to take your time and allow the process to do its work. For small areas or if you are removing epoxy paint, you can use chemicals, such as acetone to soften the epoxy. For the removal of epoxy flooring, you may need to use a commercial grinder.
Putting epoxy coatings over concrete is an excellent way to dress up the room and make it beautiful. It also provides a durable finish that will stand up to plenty of foot traffic and even some abuse in industrial areas. Epoxy coatings are highly customizable, so they can be used to beautify any room in the home.
If your LG phone isn’t working, check to see if there are any available software updates, clear the data and cache of the camera, enable Bluetooth on your phone and make your device discoverable by selecting your LG phone, and run your phone in Safe Mode to see if third-party apps are the problem.
Clear the cache and data in the phone app and call settings app, close all apps in the background, and do a soft reset of your Samsung phone. The contacts might not be synced if you changed the email address, or the email address isn’t set up because of a factory reset.
There are a range of steps that you need to do on your computer beforehand. When they haven’t been done it will cause the Samsung data migration tool to not complete the data migration. Such as, turning off background programs, fixing any disk errors, and doing a disk defrag.
For troubleshooting methods to change the resolution on your Vizio TV, try resetting your TV to stop any unwanted resolution changes ongoing content, turn off the ‘Zoom Mode’ within the ‘System Options” menu, and be sure you are changing the aspect ratio for any ‘Wide Mode’ needs.
For questions concerning a factory reset on a Vizio TV, the factory reset code is ‘0000’ if not previously changed to a specific code, try resetting your device if you encounter issues with the TV locking up while in the middle of a reset, and disconnect your device from power to complete a reset.
If your Vizio TV has dark spots, it could be that an LED strip has gone out, that a display panel has been damaged, causing it to have difficulty retaining pixels, or it might be a problem that can be resolved by resetting the TV if dark spots randomly come and go.
If your Vizio TV menu keeps popping up, the most common cause is that either the menu button is stuck or another button on your remote is stuck. To see if this is the problem, remove the batteries from the remote and rapidly click the menu button as well as all other buttons on the remote.
If your Vizio TV has no signal when on the RGB input, this is because this input option is only to be used to connect through video signal with a computer. Therefore, if no computer is connected and you are trying to complete a different function on the input, no signal will be present.
Oftentimes, auto-rotate can simply experience glitches or ‘freeze’ if there is an open app that you used auto-rotate on, but is currently in the background. While it may not seem like it would affect your phone, it’s good practice to restart it at least once or twice a week. This can prevent issues like auto-rotate not working.
If your Samsung Soundbar Remote is not working and the Remote won’t ID set, turn the soundbar off. Then press on the Volume or Up button on the soundbar’s remote. Hold this button down for about six seconds until you see the message of ID Set on your Samsung Soundbar Remote.
If your Samsung Smart Switch is having connection problems, and your USB connection is unsupported, see that your USB is completely plugged into the USB port. Try different USB ports or USB cables. You will see a notification indicating Allow MTP Connection which you will need to confirm as enabled.
When you have a Samsung Galaxy touch screen not working, the problem may be an easy fix. Your touch screen may be blurry, frozen, operating …
If your Samsung Smart Switch is not transferring videos, go to Gallery and delete any videos that are not absolutely important to you. You can also go to Settings and then Apps and delete any video apps that are taking up a lot of space. You can also delete the video cache data.
If your dryer buzzes and smells burnt as well, check out the dryer belt to make sure it is not damaged. Also, examine the idler pulley that keeps tension of the dryer belt. You may need to replace the entire idler pulley assembly with a brand new one.
If your Vizio TV is having issues with screen mirroring, make sure you are using a Chromecast-compatible app and device. Ensure that the devices are on the same network. Disable power saving options on the streaming device. Try restarting the TV, streaming device, and router.
If your dryer timer is not working and the dryer timer is making a humming sound, first check for anything that could be preventing the dryer drum from spinning. Check for any coins or objects that could be lodged between the dryer drum and the dryer housing.
If your dryer sensor is not working and neither is the dryer fabric sensor, you may need to replace the dryer’s inlet control thermostat. To do so, remove the screws holding the inlet control thermostat and take out the non-functioning inlet control thermostat.
If you have a dryer filter problem and the dryer is shutting down and the change filter light is on but the filter is clean, first clean out the dryer filter. Then try re-booting the dryer by unplugging it and pressing on the Start/Pause button for approximately eight to ten seconds. Then, plug the dryer back in and restart it and check if the problem is resolved.
It could be something on your phone that is causing the battery drain or a battery not holding a charge. Google is a common culprit for this. Try uninstalling your Google suite or anything that uses Google. Reset your phone and this may take it to its default positions. Try charging your phone again to see if it keeps happening.
If your Sanyo TV Remote is not working and its red light is blinking, check your Bluetooth connection and pairing. Make sure that the Sanyo TV Remote is in full synchronization with your Sanyo TV. Also, make sure all batteries in the Sanyo TV Remote are fully charged.
Take the batteries out, and put them back in. Then restart your Google Chromecast, and your TV by turning them at the wall outlet then turning them back on again. After that, verify the remote is set up correctly in the ‘remote and accessories’ option in the settings of Google TV.