Is your Dell monitor screen black? It is likely a problem with the power. Check all cables, including the power cable for damage. Update any old cables, including HDMI and DVI. Bypass any power strip or UPS device and plug the monitor directly into the wall.
When your Dell laptop charger is not working, resetting the device will often start it working again. Shut down the computer fully, remove all cables, and remove the battery. Hold down the power button for 30 seconds, reinsert the battery, and restart the laptop. It may be a damaged charger or a power problem in the area where you are charging it.
When your Samsung TV cast is not working, a hard reset can be performed easily. Turn the TV on, unplug it from the wall and wait 30 seconds. After you plug the TV back in and turn it on using the power button, the memory will be refreshed. This will often fix any casting problems that you are having.
A full and hard reset will often fix most Firestick and Samsung TV problems. Unplug the Firestick and disconnect it from the TV. Unplug the TV while the power is on. Wait 5 minutes before plugging in the TV and pushing the power button. You can then reconnect the Firestick and give it time to reboot.
Anytime your Samsung TV Guide is not working you should perform a hard restart on the TV. Make sure that the power is on and the TV is operating. Unplug the power cord from the wall and wait a few minutes before plugging it back in again. Press the power button to finish restarting the TV. Your memory cache will now be flushed and you will be working with a clear memory.
To get your Alienware monitor working properly, unplug the cord from the monitor and plug it back in again firmly. Bypass any UPS or power strip and plug it into a receptacle you know works. Verify that the power cord is free of damage and is operating properly.
When your Lenovo monitor is not working, try to enter the BIOS screen. You may be able to change the settings in the BIOS to get it working. You should also check the power as well as checking the cables used to connect the monitor to the PC. They should be tight, new, and free of visible damage.
If you have a Dell laptop battery problem, it is often associated with an aging battery that is reaching the end of its lifecycle. Replacing the battery is one of the only ways to fix this problem, aside from always operating the laptop while it is plugged in. If it is not charging or working, even with the AC adapter plugged in, it could be an issue with the AC adapter as well.
If your screen is dimmed, the monitor will be dim. There should be a key in the upper row of keys (the F keys) that allows you to adjust the screen brightness. It can also be done in the action center at the lower right-hand side of your windows desktop, beside the clock.
When the screen mirroring is not working on your Samsung TV, it is likely a problem with the Wi-Fi. Wi-Fi is used to send the signal from your secondary device to the TV so if there are any hiccups along the way, it will not work. Try restarting your router by unplugging it and waiting five minutes before you plug it back in again. That is often enough to fix the problem.
If your Hp monitor is not being detected, check the display adapter. A USB adapter for extra video output is needed to create a separate video signal. Otherwise, your adapter will be duplicating the same video signal causing your second monitor to have no picture.
Begin by checking the internet connection on your smart TV. If your internet is connected and working fine, then remove the Wi-Fi connection in the settings and re-add it. After that, verify the region is set correctly. If none of these steps work then factory reset your smart TV.
If YouTube AirPlay isn’t working, update the app with any available software updates, update the secondary device you are AirPlaying to with the most recent software, reset your router, and use AirPlay through the app itself rather than through system preferences.
Anytime the Samsung TV app store is not working, you can reset it by cold booting the TV. From the remote, press the power button and hold it while the TV turns off and back on again. From the TV, start with the TV on, unplug the TV, and then plug it back in after 30 seconds. The process is now complete and your app store should be working.
If your Samsung monitor isn’t working, try resetting the monitor, confirm that the network has been set up properly on the monitor, confirm all wires are properly inserted before setting up your network, connect to another video output on the monitor, and try changing the screen source.
If your Dell monitor is not turning on, it could be that the PSU board has failed, which will need to be prepared by a professional. It could also be caused by a defective monitor, which will be indicated during the STFC system scan portion, and complete a monitor self test.
Our top reason for Samsung TV Bixby not working is a problem with the smart remote. Many people will replace the remote when actually, it’s the batteries that need replacing. Bixby may stop working before the other functions of the remote stop working as the battery get low.
Anytime your Hisense remote is not working, check the batteries first. They may need replacing or they may have been inserted backward. Replacing the batteries with fresh, new batteries will allow a stronger signal to reach the TV from the remote. If the problem is not the batteries, there may be something obstructing the signal between the remote and the TV.
If Netflix is not working with Airplay, this is due to airplay being discontinued on the streaming platform. Netflix cannot be used with airplay, but it can still be accessed on different smart devices by either downloading the app or using a streaming stick to allow the app on some TVs.
Anytime your sharp TV remote is not working, the first step to getting it working again is changing the batteries. It’s an easy step that is all too often overlooked. Use high-quality batteries and make sure they are installed in the remote control properly. Otherwise, there may be something blocking the signal between the remote control and the TV.
Anytime your Phillips TV remote is not working you should check the batteries. Low batteries will cause the remote to act sluggish and it may be difficult to get the TV to respond unless you are very close to it or the remote is pointing directly at it. Keep some fresh batteries on hand and replace them periodically to get the most out of your TV viewing.
As a last resort, if your soundbar is not working correctly after trying several diagnostics and checks, a factory reset maybe your best option. This step will return the device by to the original factory settings. The soundbar manual will walk you through the steps to do this.
The wireless signal can be malfunctioning, the infrared signal can be blocked, the internal computer on the remote and/or your TV needs to be restarted, or there is a power issue caused by empty batteries or debris on the battery terminals. Apply the steps explained at the top of this article.
Go ahead and click on Restart and then on F2 in order to reenter the BIOS that manages the flow of information from your Dell computer’s operating system to external devices such as your Dell Computer Keyboard. Determine if the keyboard is still not working in BIOS.
Press Menu on the Remote Control and then press System. Then press on Reset and Admin. Select Soft Power Cycle while powering off your router. Now check and see if your Vizio SmartCast TV is functioning properly. See if the White LCD Power Light is on.
Anytime your Asus monitor is not working, check the power supply and the condition of the cables. If you see any problem with the cables, replace them with the latest technology. Otherwise, it could be a problem with the graphics card in your computer.
Typically, you are not getting any response from your Acer monitor because it is not getting signals from your computer. Inspect the HDMI or DVI cable that goes from the computer to the monitor for damage. Unplug the cable and turn it around so that the different ends plug into the computer and monitor. Often, this will help it to work.
If the Dish remote will not control or change the TV volume, check the cable connections. A loose cable connection will disrupt the communication between the receiver and the TV. Also, make sure the cables are connected to the right ports of any other electronic devices.
If your Benq monitor is experiencing problems, it is likely an issue with a cable. It could be a power cable, an HDMI cable, or any other cable that operates the monitor. Inspect the cables and make sure that they are new because the technology has changed over the years. There are other reasons why a monitor may fail as well, including drivers and software conflicts.
When your Sceptre monitor is not working, try the power cable to see if it needs some attention. It should be well seated into the monitor and plugged into a receptacle that is currently hot. Do not plug the monitor into a power strip if you are experiencing problems with it. If the power cord is damaged, it should be replaced.
When a ViewSonic monitor is not working, it is often a power problem. Disconnect all cables, including the cable between the computer and the monitor. Inspect them for any damage and if they are damaged or older, they should be replaced. You may also need to restart the computer fully to get the monitor working again.
On average, there are seven steps to take that should help if your Roku Soundbar is not turned on. The first step is to turn on both your Roku receiver, your Roku Soundbar, and your TV. Go to the settings menu on your TV and select ‘control other devices.
If your HP Printer isn’t working, be sure the paper is properly engaged with the roller, confirm that the scanner has been enabled, update the firmware on the printer, reestablish communication between your printer and PC, and try completing a hard reset on the device.
First, try a Hard Reset in case the TV processor has simply just frozen up. If this does not work, check for common indications that the TV’s mainboard is faulty or malfunctioning. This would include common problems such as no picture on the screen or no sound emanating from the speakers.
Unplug the USB cable from the HP Envy printer. Then go to Control Panel Programs and Features. Select all the HP Envy Printer entries and uninstall them. Go to Devices and Printer. Install the latest HP Printer Drivers and under Printer Assistance select Scan to Computer.